درباره ما
Standard Test Method for Simulated Service Corrosion Testing of Non-Aqueous Engine Coolants
ASTM D8034/D8034M-24
Organization:
ASTM - ASTM International
Year: 2024
Abstract: 5.1 This test method, by a closer approach to engine cooling system conditions, provides better evaluation and selective screening of engine coolants than is possible from glassware testing (Test Method D7935/D7935M). The improvement is achieved by controlled circulation of the coolant, by the use of automotive cooling system components, and by a greater ratio of metal surface area to coolant volume. 5.2 Although this test method provides improved discrimination, it cannot conclusively predict satisfactory corrosion inhibition and service life. If greater assurance of satisfactory performance is desired, it should be obtained from full-scale engine tests and from field testing in actual service. 5.3 Significance and interpretation of the test and its limitations are discussed further in Appendix X1. 5.4 The substitution of components in the apparatus of Section 6 is permissible if agreed upon by the contracting parties.
Collections
:
-
Statistics
Standard Test Method for Simulated Service Corrosion Testing of Non-Aqueous Engine Coolants
Show full item record
| contributor author | ASTM - ASTM International | |
| date accessioned | 2025-09-30T17:59:53Z | |
| date available | 2025-09-30T17:59:53Z | |
| date copyright | 2024 | |
| date issued | 2024 | |
| identifier other | d8034_d8034m-24.pdf | |
| identifier uri | https://yse.yabesh.ir/std/handle/yse/341055 | |
| description abstract | 5.1 This test method, by a closer approach to engine cooling system conditions, provides better evaluation and selective screening of engine coolants than is possible from glassware testing (Test Method D7935/D7935M). The improvement is achieved by controlled circulation of the coolant, by the use of automotive cooling system components, and by a greater ratio of metal surface area to coolant volume. 5.2 Although this test method provides improved discrimination, it cannot conclusively predict satisfactory corrosion inhibition and service life. If greater assurance of satisfactory performance is desired, it should be obtained from full-scale engine tests and from field testing in actual service. 5.3 Significance and interpretation of the test and its limitations are discussed further in Appendix X1. 5.4 The substitution of components in the apparatus of Section 6 is permissible if agreed upon by the contracting parties. | |
| language | English | |
| title | Standard Test Method for Simulated Service Corrosion Testing of Non-Aqueous Engine Coolants | en |
| title | ASTM D8034/D8034M-24 | num |
| type | standard | |
| status | Active | |
| tree | ASTM - ASTM International:;2024 | |
| contenttype | fulltext | |
| scope | 1.1 This test method covers the effect of a circulating engine coolant on metal test specimens and automotive cooling system components under controlled, essentially isothermal laboratory conditions. 1.2 This test method specifies test material, cooling system components, type of coolant, and coolant flow conditions that are considered typical of current automotive use. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. Some values have only SI units because the inch-pound equivalents are not used in practice. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Section 7. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. | |
| identifier DOI | 10.1520/D8034_D8034M-24 |