درباره ما
Standard Test Method for Analysis of Aluminum and Aluminum Alloys by Inductively Coupled Plasma Atomic Emission Spectrometry (Performance Based)
ASTM E3061-24
Organization:
ASTM - ASTM International
Year: 2024
Abstract: 5.1 This test method for the analysis of aluminum and aluminum alloys is primarily intended to test material for compliance with The Aluminum Association Inc.5 registered composition limits or other specified composition limits for aluminum and aluminum alloys. 5.2 It is assumed that all who use this test method will be trained analysts capable of performing common laboratory procedures skillfully and safely, and that the work will be performed in a properly equipped laboratory. 5.3 This is a performance-based test method that relies more on the demonstrated quality of the test result than on strict adherence to specific procedural steps. It is expected that laboratories using this test method will prepare their own work instructions. These work instructions should include detailed operating instructions for the specific laboratory, the specific reference materials employed, and performance acceptance criteria.
Collections
:
-
Statistics
Standard Test Method for Analysis of Aluminum and Aluminum Alloys by Inductively Coupled Plasma Atomic Emission Spectrometry (Performance Based)
Show full item record
| contributor author | ASTM - ASTM International | |
| date accessioned | 2025-09-30T18:01:22Z | |
| date available | 2025-09-30T18:01:22Z | |
| date copyright | 2024 | |
| date issued | 2024 | |
| identifier other | e3061-24.pdf | |
| identifier uri | https://yse.yabesh.ir/std/handle/yse/341405 | |
| description abstract | 5.1 This test method for the analysis of aluminum and aluminum alloys is primarily intended to test material for compliance with The Aluminum Association Inc.5 registered composition limits or other specified composition limits for aluminum and aluminum alloys. 5.2 It is assumed that all who use this test method will be trained analysts capable of performing common laboratory procedures skillfully and safely, and that the work will be performed in a properly equipped laboratory. 5.3 This is a performance-based test method that relies more on the demonstrated quality of the test result than on strict adherence to specific procedural steps. It is expected that laboratories using this test method will prepare their own work instructions. These work instructions should include detailed operating instructions for the specific laboratory, the specific reference materials employed, and performance acceptance criteria. | |
| language | English | |
| title | Standard Test Method for Analysis of Aluminum and Aluminum Alloys by Inductively Coupled Plasma Atomic Emission Spectrometry (Performance Based) | en |
| title | ASTM E3061-24 | num |
| type | standard | |
| status | Active | |
| tree | ASTM - ASTM International:;2024 | |
| contenttype | fulltext | |
| scope | 1.1 This test method describes the inductively coupled plasma atomic emission spectrometric analysis of aluminum and aluminum alloys for the following elements: Elements Application Range, % Minimum Maximum Si 0.02 16.8 Fe 0.02 3.06 Cu 0.005 7.0 Mn 0.003 1.41 Mg 0.006 8.2 Cr 0.004 0.52 Ni 0.004 2.71 Zn 0.02 9.65 Ti 0.009 0.20 Ag 0.003 0.4 As 0.005 0.012 B 0.009 0.027 Ba 0.002 0.03 Be 0.002 0.11 Bi 0.01 0.59 Ca 0.003 0.048 Cd 0.002 0.055 Co 0.002 0.034 Ga 0.01 0.019 Li 0.001 2.48 Mo 0.02 0.15 Na 0.008 0.026 P 0.01 0.025 Pb 0.009 0.51 Sb 0.01 0.28 Sc 0.01 0.065 Sn 0.008 6.28 Sr 0.0008 0.028 Ti 0.005 0.20 Tl 0.009 0.13 V 0.01 0.12 Zr 0.004 0.25 1.2 This test method has only been interlaboratory tested for the elements and ranges specified. It may be possible to extend this test method to other elements or different composition ranges if method validation, which includes evaluation of method sensitivity and precision and bias (as described in Section 14), is performed. Additionally, the validation study must evaluate the acceptability of sample preparation methodology using reference materials or spike recoveries, or both. The user should carefully evaluate the validation data against the laboratory’s data quality objectives. Method validation of scope extensions is also a requirement of ISO/IEC 17025. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Safety hazard statements are given in Section 10 and specific warning statements are given in Sections 15, 17, 18, 19, 20 and 21. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. | |
| identifier DOI | 10.1520/E3061-24 |