درباره ما
Standard Specification for Implantable Polytetrafluoroethylene (PTFE) Sheet, Tube, and Rod Shapes Fabricated from Granular Molding Powders
ASTM F754-24
Organization:
ASTM - ASTM International
Year: 2024
Abstract: 3.1 Fabricated PTFE meeting the requirements of this specification can be expected to exhibit consistent and reproducible chemical, physical, and biological properties. 3.1.1 This specification provides an analytic method to extract organic contaminants from fabricated configurations, which includes a limit to the presence of residual adulterants, additives, or processing aids. 3.1.2 This specification addresses the characteristics of virgin raw granular molding powders obtained from resin manufacturers and used for producing implant configurations.
Collections
:
-
Statistics
Standard Specification for Implantable Polytetrafluoroethylene (PTFE) Sheet, Tube, and Rod Shapes Fabricated from Granular Molding Powders
Show full item record
| contributor author | ASTM - ASTM International | |
| date accessioned | 2025-09-30T18:01:49Z | |
| date available | 2025-09-30T18:01:49Z | |
| date copyright | 2024 | |
| date issued | 2024 | |
| identifier other | f0754-24.pdf | |
| identifier uri | https://yse.yabesh.ir/std/handle/yse/341519 | |
| description abstract | 3.1 Fabricated PTFE meeting the requirements of this specification can be expected to exhibit consistent and reproducible chemical, physical, and biological properties. 3.1.1 This specification provides an analytic method to extract organic contaminants from fabricated configurations, which includes a limit to the presence of residual adulterants, additives, or processing aids. 3.1.2 This specification addresses the characteristics of virgin raw granular molding powders obtained from resin manufacturers and used for producing implant configurations. | |
| language | English | |
| title | Standard Specification for Implantable Polytetrafluoroethylene (PTFE) Sheet, Tube, and Rod Shapes Fabricated from Granular Molding Powders | en |
| title | ASTM F754-24 | num |
| type | standard | |
| status | Active | |
| tree | ASTM - ASTM International:;2024 | |
| contenttype | fulltext | |
| scope | 1.1 This specification describes the physical, chemical, and mechanical performance requirements for polytetrafluoroethylene (PTFE) pre-fabricated by compression molding or extrusion into sheet, tube, and rod shapes which may be used for implant products. 1.2 PTFE is a high molecular weight straight chain member of the generic class of perfluorocarbon (containing only the elements fluorine and carbon) polymers. 1.3 Perfluorocarbon high polymers exhibit extraordinary thermal and chemical stability and do not require stabilizing additives of any kind. 1.4 This specification applies to primarily void-free molded or extruded PTFE shapes formed from granular molding powders. This specification does not apply to shapes formed from “fine powder” resins by lubricated paste extrusion, which includes expanded PTFE. 1.5 This specification does not apply to specific surgical implant products, including their packaging, sterilization, or material biocompatibility and/or suitability for a particular end-use application. 1.6 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. | |
| identifier DOI | 10.1520/F0754-24 |