درباره ما
Standard Specification for Polyethylene (PE) Large Diameter Profile Wall Sewer and Drain Pipe
ASTM F894-24
Organization:
ASTM - ASTM International
Year: 2024
Abstract: This specification covers requirements and test methods for materials, dimensions, workmanship, ring stiffness, flattening, joint systems, and a form of marking for polyethylene (PE) pipe of profile wall construction and with bell and spigot, heat fusion, extrusion welded or electrofusion joints for use in gravity flow applications, such as for sewers and drains. The PE profile wall pipe products cover six standard ring stiffness constant (RSC) classifications, namely 40, 63, 100, and 160, 250 and 400. These are referred to as RSC 40, RSC 63, RSC 100, RSC 160, RSC 250 and RSC 400. Referee testing, ring stiffness constant testing, flattening test, and joint tightness test shall be performed to meet the requirements prescribed.
Collections
:
-
Statistics
Standard Specification for Polyethylene (PE) Large Diameter Profile Wall Sewer and Drain Pipe
Show full item record
| contributor author | ASTM - ASTM International | |
| date accessioned | 2025-09-30T18:01:51Z | |
| date available | 2025-09-30T18:01:51Z | |
| date copyright | 2024 | |
| date issued | 2024 | |
| identifier other | f0894-24.pdf | |
| identifier uri | https://yse.yabesh.ir/std/handle/yse/341528 | |
| description abstract | This specification covers requirements and test methods for materials, dimensions, workmanship, ring stiffness, flattening, joint systems, and a form of marking for polyethylene (PE) pipe of profile wall construction and with bell and spigot, heat fusion, extrusion welded or electrofusion joints for use in gravity flow applications, such as for sewers and drains. The PE profile wall pipe products cover six standard ring stiffness constant (RSC) classifications, namely 40, 63, 100, and 160, 250 and 400. These are referred to as RSC 40, RSC 63, RSC 100, RSC 160, RSC 250 and RSC 400. Referee testing, ring stiffness constant testing, flattening test, and joint tightness test shall be performed to meet the requirements prescribed. | |
| language | English | |
| title | Standard Specification for Polyethylene (PE) Large Diameter Profile Wall Sewer and Drain Pipe | en |
| title | ASTM F894-24 | num |
| type | standard | |
| status | Active | |
| tree | ASTM - ASTM International:;2024 | |
| contenttype | fulltext | |
| scope | 1.1 This specification covers requirements and test methods for materials, dimensions, workmanship, ring stiffness, flattening, joint systems, and a form of marking for large diameter, 10 in. to 138 in. (250 mm to 3510 mm), inside diameter based polyethylene (PE) pipe of profile wall construction and with bell and spigot, heat fusion, extrusion welded or electrofusion joints for use in gravity flow applications, such as for sewers and drains. Note 1: Pipe produced to this specification should be installed in accordance with Practice D2321 and with the manufacturer's recommendations. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 The following safety hazards caveat pertains only to the test method portion, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. | |
| identifier DOI | 10.1520/F0894-24 |