Standard Test Method for Finite Element Analysis (FEA) of Non-Modular Metallic Orthopaedic  Hip Femoral Stems

ASTM - ASTM International

ASTM F2996-24

Organization:

Year: 2024

Abstract: 3.1 This standard is applicable to the calculation of stresses seen on a femoral hip stem when loaded in a manner described in ISO 7206-4. This method can be used to establish the worst-case size for a particular implant. When stresses calculated using this method were compared to the stresses measured from physical strain gauging techniques performed at two laboratories using two different methods, the results correlated to within 8 %. 3.2 This test method can be used to estimate the effects of design variables on the stress and strain of metallic hip femoral stems in a setup mimicking that described in ISO 7206-4.

URI: https://yse.yabesh.ir/std/handle/yse/341683

Collections :

ASTM - ASTM International

Download PDF : (1.869Mb)
Show Full MetaData Hide Full MetaData
Statistics

Standard Test Method for Finite Element Analysis (FEA) of Non-Modular Metallic Orthopaedic Hip Femoral Stems

Show full item record

contributor author	ASTM - ASTM International
date accessioned	2025-09-30T18:02:27Z
date available	2025-09-30T18:02:27Z
date copyright	2024
date issued	2024
identifier other	f2996-24.pdf
identifier uri	https://yse.yabesh.ir/std/handle/yse/341683
description abstract	3.1 This standard is applicable to the calculation of stresses seen on a femoral hip stem when loaded in a manner described in ISO 7206-4. This method can be used to establish the worst-case size for a particular implant. When stresses calculated using this method were compared to the stresses measured from physical strain gauging techniques performed at two laboratories using two different methods, the results correlated to within 8 %. 3.2 This test method can be used to estimate the effects of design variables on the stress and strain of metallic hip femoral stems in a setup mimicking that described in ISO 7206-4.
language	English
title	Standard Test Method for Finite Element Analysis (FEA) of Non-Modular Metallic Orthopaedic Hip Femoral Stems	en
title	ASTM F2996-24	num
type	standard
status	Active
tree	ASTM - ASTM International:;2024
contenttype	fulltext
scope	1.1 This standard establishes requirements and considerations for the numerical simulation of non-modular (that is, limited to monolithic stems with only a femoral head/trunnion taper interface) metallic orthopaedic hip stems using Finite Element Analysis (FEA) techniques for the estimation of stresses and strains. This standard is only applicable to stresses below the yield strength, as provided in the material certification. 1.2 Purpose—This test method establishes requirements and considerations for the development of finite element models to be used in the evaluation of non-modular metallic orthopaedic hip stem designs for the purpose of prediction of the static implant stresses and strains. The context of use is to apply the finite element method to identify the worst-case size within a series of different sizes of the same implant design and to subsequently test that worst-case size (as is typically required). Recommended procedures for performing model checks and verification are provided to help determine if the analysis follows recommended guidelines. Finally, the recommended content of an engineering report covering the mechanical simulation is presented. 1.3 Limits—This test method is limited in discussion to the static structural analysis of non-modular metallic orthopaedic hip stems (which excludes the prediction of fatigue strength). 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
identifier DOI	10.1520/F2996-24