درباره ما
Standard Specification for Nickel-Coated Soft or Annealed Copper Wire
ASTM B355-11
Organization:
ASTM - ASTM International
Year: 2024
Abstract: This specification covers nickel-coated, soft or annealed, round copper wire for use in electrical equipment. Five classes of wire are covered as follows: Class 2, Class 4, Class 7, Class 10, and Class 27. Properties like elongation, resistivity and dimensions of the wire shall be determined. The continuity of the coating shall be determined by the sodium polysulfide test. Adherence of the coating shall be determined by wrapping and immersion tests.
Collections
:
-
Statistics
Standard Specification for Nickel-Coated Soft or Annealed Copper Wire
Show full item record
| contributor author | ASTM - ASTM International | |
| date accessioned | 2025-09-30T18:03:23Z | |
| date available | 2025-09-30T18:03:23Z | |
| date copyright | 2024 | |
| date issued | 2024 | |
| identifier other | b0355-11r24.pdf | |
| identifier uri | https://yse.yabesh.ir/std/handle/yse/341926 | |
| description abstract | This specification covers nickel-coated, soft or annealed, round copper wire for use in electrical equipment. Five classes of wire are covered as follows: Class 2, Class 4, Class 7, Class 10, and Class 27. Properties like elongation, resistivity and dimensions of the wire shall be determined. The continuity of the coating shall be determined by the sodium polysulfide test. Adherence of the coating shall be determined by wrapping and immersion tests. | |
| language | English | |
| title | Standard Specification for Nickel-Coated Soft or Annealed Copper Wire | en |
| title | ASTM B355-11 | num |
| type | standard | |
| status | Active | |
| tree | ASTM - ASTM International:;2024 | |
| contenttype | fulltext | |
| scope | 1.1 This specification covers nickel-coated, soft or annealed, round copper wire for use in electrical equipment. 1.2 Five classes of wire are covered as follows: 1.2.1 Class 2—Wire whose nickel coating is at least 2 % of the total weight of the coated wire. 1.2.2 Class 4—Wire whose nickel coating is at least 4 % of the total weight of the coated wire. 1.2.3 Class 7—Wire whose nickel coating is at least 7 % of the total weight of the coated wire. 1.2.4 Class 10—Wire whose nickel coating is at least 10 % of the total weight of the coated wire. 1.2.5 Class 27—Wire whose nickel coating is at least 27 % of the total weight of the coated wire. Note 1: For information purposes, the thickness of coating in microinches provided by the percentages listed in 1.2 is shown in Table 1. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parenthesis are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3.1 Exceptions—The SI values for density, resistivity, and volume are to be regarded as standard. 1.4 This hazard statement applies only to Section 6, Test Methods, and to the Appendix of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. | |
| identifier DOI | 10.1520/B0355-11R24 |