درباره ما
Standard Specification for Welded Wire Mesh Fence Fabric (Metallic-Coated or Polymer Coated) for Meshes of 6 in.2 [3871 mm2] or Less, in Panels or Rolls, with Uniform Meshes
ASTM F2453/F2453M-14
Organization:
ASTM - ASTM International
Year: 2025
Abstract: This specification covers welded wire mesh fence fabric produced from steel wire or metallic-coated steel wire. The metallic-coated fabric may be polymer coated after fabrication. Welded wire mesh fence fabric is classified in accordance with coating as follows: Type 1; Type 2; Type 3; and Type 4. Tests shall be performed to determine the properties of the material in accordance with the following test methods: metallic coating weight; polymer coating thickness; polymer adhesion test; and weld shear strength of fabric.
Collections
:
-
Statistics
Standard Specification for Welded Wire Mesh Fence Fabric (Metallic-Coated or Polymer Coated) for Meshes of 6 in.<sup>2</sup> [3871 mm<sup>2</sup>] or Less, in Panels or Rolls, with Uniform Meshes
Show full item record
| contributor author | ASTM - ASTM International | |
| date accessioned | 2025-09-30T19:20:13Z | |
| date available | 2025-09-30T19:20:13Z | |
| date copyright | 2025 | |
| date issued | 2025 | |
| identifier other | f2453_f2453m-14r25.pdf | |
| identifier uri | https://yse.yabesh.ir/std/handle/yse/342912 | |
| description abstract | This specification covers welded wire mesh fence fabric produced from steel wire or metallic-coated steel wire. The metallic-coated fabric may be polymer coated after fabrication. Welded wire mesh fence fabric is classified in accordance with coating as follows: Type 1; Type 2; Type 3; and Type 4. Tests shall be performed to determine the properties of the material in accordance with the following test methods: metallic coating weight; polymer coating thickness; polymer adhesion test; and weld shear strength of fabric. | |
| language | English | |
| title | Standard Specification for Welded Wire Mesh Fence Fabric (Metallic-Coated or Polymer Coated) for Meshes of 6 in.2 [3871 mm2] or Less, in Panels or Rolls, with Uniform Meshes | en |
| title | ASTM F2453/F2453M-14 | num |
| type | standard | |
| status | Active | |
| tree | ASTM - ASTM International:;2025 | |
| contenttype | fulltext | |
| scope | 1.1 This specification covers welded wire mesh fence fabric produced from steel wire or metallic-coated steel wire. The metallic-coated fabric may be polymer coated after fabrication. 1.2 Welded wire mesh fence fabric is produced in four types, based on the kind of coating, as described in Section 4. 1.3 This specification is applicable to orders in either inch-pound units or SI units. Values stated in either inch-pound or SI units are to be regarded separately as the standard. Within the text, the SI units are shown in brackets. The values in the two systems are not exact equivalents; therefore, each system shall be used independent of the other, without combining values in any way. 1.4 This specification references notes and footnotes, which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of this specification. 1.5 The following safety hazards caveat pertains only to the test methods portion, Section 13, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations proper to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. | |
| identifier DOI | 10.1520/F2453_F2453M-14R25 |