MIL-I-81969B
INSTALLING AND REMOVAL TOOLS, CONNECTOR ELECTRICAL CONTACTS, TYPE II, CLASS 2, COMPOSITION C
Organization:
DLA - CC - DLA Land and Maritime
Year: 1982
Abstract: This specification covers the general requirements for installing and removal tools for use in installing and removing electrical contacts used in connectors and other electrical and electronic components (see 6.1).
Installing and removal tools covered by this specification shall be of the following types, classes, and compositions, as specified (see 3.1 and 6.2):
Beneficial comments (additions, deletions, recommendations) and any pertinent data which may be of use in improving this document should be addressed to: Engineering Specifications and Standards Department (ESSD) (Code 93), Naval Air Engineering Center, Lakehurst, NJ 08733 by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter.
The military part number shall consist of the letter "M," the basic number of the specification sheet, and an assigned dash number (see 3.1) as shown in the following:
Intended Use: The installing and removal tools covered by this specification are intended to install and remove removable electric contacts used in electric connectors and other electric and electronic equipment as specified in MIL-STD-1646. Acquisition documents should specify the following: a. Title, number and date of this specification. b. Title, number and date of the applicable specification sheet, type and size required, and the complete part number (see 1.2 and 3.1). With respect to products requiring qualification, awards will be made only for products which are at the time set for opening of bids, qualified for inclusion in the applicable Qualified Products List whether or not such products have actually been so listed by that date. The attention of the contractors is called to these requirements, and manufacturers are urged to arrange to have the products that they propose to offer to the Federal Government tested for qualification in order that they be eligible to be awarded contracts or orders for the products covered by this specification. The activity responsible for the qualified products list is the Naval Air Systems Command, Washington, D.C. 20361; however, information pertaining to qualification of products may be obtained from the Naval Avionics Center, Code 714, 6000 East 21st Street, Indianapolis, IN 46218. The maximum and minimum wire sizes shall be the military wires in the applicable military connector specification. All tools covered by this specification are non-repairable. In plunger type removal tools, the probe and plunger shall be permanently attached to the body of the tool. See Table III. The margins of this specification are marked with an asterisk to indicate where changes (additions, modifications, corrections, deletions) from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue.
Installing and removal tools covered by this specification shall be of the following types, classes, and compositions, as specified (see 3.1 and 6.2):
TYPE I - Installing tool. II - Removal tool. III - Combination installing and removal tool. CLASS 1 - Front release of contacts. 2 - Rear release of contacts. 3 - Side release of contacts. COMPOSITION A - Metal. B - Plastic. C - Combination metal and plastic.
Beneficial comments (additions, deletions, recommendations) and any pertinent data which may be of use in improving this document should be addressed to: Engineering Specifications and Standards Department (ESSD) (Code 93), Naval Air Engineering Center, Lakehurst, NJ 08733 by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter.
The military part number shall consist of the letter "M," the basic number of the specification sheet, and an assigned dash number (see 3.1) as shown in the following:
Intended Use: The installing and removal tools covered by this specification are intended to install and remove removable electric contacts used in electric connectors and other electric and electronic equipment as specified in MIL-STD-1646. Acquisition documents should specify the following: a. Title, number and date of this specification. b. Title, number and date of the applicable specification sheet, type and size required, and the complete part number (see 1.2 and 3.1). With respect to products requiring qualification, awards will be made only for products which are at the time set for opening of bids, qualified for inclusion in the applicable Qualified Products List whether or not such products have actually been so listed by that date. The attention of the contractors is called to these requirements, and manufacturers are urged to arrange to have the products that they propose to offer to the Federal Government tested for qualification in order that they be eligible to be awarded contracts or orders for the products covered by this specification. The activity responsible for the qualified products list is the Naval Air Systems Command, Washington, D.C. 20361; however, information pertaining to qualification of products may be obtained from the Naval Avionics Center, Code 714, 6000 East 21st Street, Indianapolis, IN 46218. The maximum and minimum wire sizes shall be the military wires in the applicable military connector specification. All tools covered by this specification are non-repairable. In plunger type removal tools, the probe and plunger shall be permanently attached to the body of the tool. See Table III. The margins of this specification are marked with an asterisk to indicate where changes (additions, modifications, corrections, deletions) from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue.
Collections
:
Show full item record
| contributor author | DLA - CC - DLA Land and Maritime | |
| date accessioned | 2017-09-04T15:57:25Z | |
| date available | 2017-09-04T15:57:25Z | |
| date copyright | 08/20/1982 | |
| date issued | 1982 | |
| identifier other | RAHPDAAAAAAAAAAA.pdf | |
| identifier uri | https://yse.yabesh.ir/std/handle/yse/60716 | |
| description abstract | This specification covers the general requirements for installing and removal tools for use in installing and removing electrical contacts used in connectors and other electrical and electronic components (see 6.1). Installing and removal tools covered by this specification shall be of the following types, classes, and compositions, as specified (see 3.1 and 6.2): TYPE I - Installing tool. II - Removal tool. III - Combination installing and removal tool. CLASS 1 - Front release of contacts. 2 - Rear release of contacts. 3 - Side release of contacts. COMPOSITION A - Metal. B - Plastic. C - Combination metal and plastic. Beneficial comments (additions, deletions, recommendations) and any pertinent data which may be of use in improving this document should be addressed to: Engineering Specifications and Standards Department (ESSD) (Code 93), Naval Air Engineering Center, Lakehurst, NJ 08733 by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. The military part number shall consist of the letter "M," the basic number of the specification sheet, and an assigned dash number (see 3.1) as shown in the following: Intended Use: The installing and removal tools covered by this specification are intended to install and remove removable electric contacts used in electric connectors and other electric and electronic equipment as specified in MIL-STD-1646. Acquisition documents should specify the following: a. Title, number and date of this specification. b. Title, number and date of the applicable specification sheet, type and size required, and the complete part number (see 1.2 and 3.1). With respect to products requiring qualification, awards will be made only for products which are at the time set for opening of bids, qualified for inclusion in the applicable Qualified Products List whether or not such products have actually been so listed by that date. The attention of the contractors is called to these requirements, and manufacturers are urged to arrange to have the products that they propose to offer to the Federal Government tested for qualification in order that they be eligible to be awarded contracts or orders for the products covered by this specification. The activity responsible for the qualified products list is the Naval Air Systems Command, Washington, D.C. 20361; however, information pertaining to qualification of products may be obtained from the Naval Avionics Center, Code 714, 6000 East 21st Street, Indianapolis, IN 46218. The maximum and minimum wire sizes shall be the military wires in the applicable military connector specification. All tools covered by this specification are non-repairable. In plunger type removal tools, the probe and plunger shall be permanently attached to the body of the tool. See Table III. The margins of this specification are marked with an asterisk to indicate where changes (additions, modifications, corrections, deletions) from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. | |
| language | English | |
| title | MIL-I-81969B | num |
| title | INSTALLING AND REMOVAL TOOLS, CONNECTOR ELECTRICAL CONTACTS, TYPE II, CLASS 2, COMPOSITION C | en |
| type | standard | |
| page | 16 | |
| status | Active | |
| tree | DLA - CC - DLA Land and Maritime:;1982 | |
| contenttype | fulltext |

درباره ما