درباره ما
API MPMS 8.5
Manual of Petroleum Measurement Standards Chapter 8.5 Standard Practice for Manual Piston Cylinder Sampling for Volatile Crude Oils, Condensates, and Liquid Petroleum Products - First Edition
Organization:
API - American Petroleum Institute
Year: 2015
Abstract: This practice includes the equipment and procedures for obtaining a representative sample of “live” or high vapor pressure crude oils, condensates, and/or liquid petroleum products from low pressure sample points, where there is insufficient sample point pressure to use a Floating Piston Cylinder (FPC) as described in Practice D3700.
This practice is intended for use with sample types, such as UN Class 3 Flammable Liquids, that might have been collected and transported using open containers. The use of a manual piston cylinder in place of open containers is intended to prevent the loss of volatile (light end) components, which can impact subsequent test results.
This practice is suitable for sampling crude oils, condensates, and/or liquid petroleum products having true vapor pressures less than 300 kPa (43 psia nominal) at 50 °C. This practice applies to samples that will typically fall between Practices D4057 (APIMPMS Chapter 8.1) and D3700. This practice shall not be used for materials classified as UN Class 2 Gases2(“…having a vapor pressure greater than 300 kPa at 50 °C or is completely gaseous at 20 °C at 101.3 kPa.”).
This practice allows for sampling of crude oils that flow freely at the conditions of sampling.
It is the responsibility of the user to ensure that the sampling point is located so as to obtain a representative sample.
The values stated in SI units are to be regarded as standard.
Exception—The values given in parentheses are for information only.
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
This practice is intended for use with sample types, such as UN Class 3 Flammable Liquids, that might have been collected and transported using open containers. The use of a manual piston cylinder in place of open containers is intended to prevent the loss of volatile (light end) components, which can impact subsequent test results.
This practice is suitable for sampling crude oils, condensates, and/or liquid petroleum products having true vapor pressures less than 300 kPa (43 psia nominal) at 50 °C. This practice applies to samples that will typically fall between Practices D4057 (APIMPMS Chapter 8.1) and D3700. This practice shall not be used for materials classified as UN Class 2 Gases2(“…having a vapor pressure greater than 300 kPa at 50 °C or is completely gaseous at 20 °C at 101.3 kPa.”).
This practice allows for sampling of crude oils that flow freely at the conditions of sampling.
It is the responsibility of the user to ensure that the sampling point is located so as to obtain a representative sample.
The values stated in SI units are to be regarded as standard.
Exception—The values given in parentheses are for information only.
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Collections
:
Show full item record
| contributor author | API - American Petroleum Institute | |
| date accessioned | 2017-09-04T16:08:40Z | |
| date available | 2017-09-04T16:08:40Z | |
| date copyright | 2015.12.01 | |
| date issued | 2015 | |
| identifier other | SETKNFAAAAAAAAAA.pdf | |
| identifier uri | https://yse.yabesh.ir/std/handle/yse/71920 | |
| description abstract | This practice includes the equipment and procedures for obtaining a representative sample of “live” or high vapor pressure crude oils, condensates, and/or liquid petroleum products from low pressure sample points, where there is insufficient sample point pressure to use a Floating Piston Cylinder (FPC) as described in Practice D3700. This practice is intended for use with sample types, such as UN Class 3 Flammable Liquids, that might have been collected and transported using open containers. The use of a manual piston cylinder in place of open containers is intended to prevent the loss of volatile (light end) components, which can impact subsequent test results. This practice is suitable for sampling crude oils, condensates, and/or liquid petroleum products having true vapor pressures less than 300 kPa (43 psia nominal) at 50 °C. This practice applies to samples that will typically fall between Practices D4057 (APIMPMS Chapter 8.1) and D3700. This practice shall not be used for materials classified as UN Class 2 Gases2(“…having a vapor pressure greater than 300 kPa at 50 °C or is completely gaseous at 20 °C at 101.3 kPa.”). This practice allows for sampling of crude oils that flow freely at the conditions of sampling. It is the responsibility of the user to ensure that the sampling point is located so as to obtain a representative sample. The values stated in SI units are to be regarded as standard. Exception—The values given in parentheses are for information only. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. | |
| language | English | |
| title | API MPMS 8.5 | num |
| title | Manual of Petroleum Measurement Standards Chapter 8.5 Standard Practice for Manual Piston Cylinder Sampling for Volatile Crude Oils, Condensates, and Liquid Petroleum Products - First Edition | en |
| type | standard | |
| page | 20 | |
| status | Active | |
| tree | API - American Petroleum Institute:;2015 | |
| contenttype | fulltext |