درباره ما
Browsing ASME - ASME International by Title
Now showing items 1-20 of 1083
-
Abbreviations and Acronyms for Use in Product Definition and Related Documents
Abstract: The abbreviations and acronyms, hereinafter referred to as “abbreviations,” listed in this Standard are used on engineering drawings and related documentation. Purpose The intent of this Standard is to allow the use of ... -
Abbreviations and Acronyms for Use in Product Definition and Related Documents
Abstract: The abbreviations and acronyms, hereinafter referred to as “abbreviations,” listed in this Standard are used on engineering drawings and related documentation. Purpose The intent of this Standard is to allow the use of ... -
ASME 14414
Abstract: This International Standard sets the requirements for conducting and reporting the results of a pumping system energy assessment (hereafter referenced as "assessment") that considers the entire pumping system, from energy ... -
ASME A112.1.2
Abstract: This Standard identifies methods of providing protection against backsiphonage through means of an air gap and establishes physical requirements and methods of testing air gaps for plumbing fixtures and water receptors. -
ASME A112.1.3
Abstract: This Standard establishes physical requirements and methods of testing for air gap fittings for protecting against back siphonage and back pressure backflow. -
ASME A112.1002
Abstract: Scope:This Standard covers anti-siphon fill valves intended to be installed in water closet tanks.
ASME A112.1016
Abstract: This Standard applies to automatic compensating valves intended to be installed at the point of use, where the user has access to flow or final temperature controls, and where no further mixing occurs downstream of the ...ASME A112.1016
Abstract: This Standard applies to automatic compensating valves intended to be installed at the point of use, where the user has access to flow or final temperature controls, and where no further mixing occurs downstream of the ...ASME A112.1016
Abstract: This Standard applies to automatic compensating valves intended to be installed at the point of use, where the user has access to flow or final temperature controls, and where no further mixing occurs downstream of the ...ASME A112.1070
Abstract: This Standard covers water temperature limiting devices intended to limit the hot or tempered water temperature supplied to fittings for fixtures such as sinks, bidets, lavatories, and bathtubs to reduce the risk of scalding. ...ASME A112.14.1
Abstract: This Standard establishes requirements for dimensions, performance requirements, connections, materials and finishes, testing, and marking of backwater valves. Types of backwater valves covered in this Standard include ...ASME A112.14.3
Abstract: This Standard covers general product requirements as well as the performance criteria for the testing and rating of grease interceptors, whose rated flows are 100 gpm (380 L/m) or less.ASME A112.14.3
Abstract: This Standard covers general product requirements as well as the performance criteria for the testing and rating of hydromechanical grease interceptors, rated by flow in gallons per minute (gpm) or liters per minute (L/min).ASME A112.14.4
Abstract: This Standard establishes requirements for grease interceptors that are equipped with automatic grease removal devices (GRD). It includes testing requirements and performance criteria designed to ensure conformance to ...ASME A112.14.6
Abstract: This Standard establishes requirements for FOG (Fats, Oils, and Greases) disposal systems. FOG disposal systems shall be designed to
(a) remove FOG from effluent
(b) retain separated FOG
(c) ...ASME A112.18.1
Abstract: This Standard covers plumbing supply fittings and accessories located between the supply stop and the terminal fitting, inclusive, as follows:
(a) automatic compensating valves for individual wall-mounted showering ...ASME A112.18.2
Abstract: This Standard covers plumbing waste fittings of sizes NPS-2 and smaller.
This Standard does not cover
(a) plumbing supply fittings, which are covered by ASME A112.18.1/CSA B125.1;
(b) other devices (e.g., ...ASME A112.18.2
Abstract: Scope:This Standard covers plumbing waste fittings of sizes NPS-2 and smaller.
This ...
ASME A112.18.3
Abstract: This Standard addresses functional performance and requires physical characteristics of devices and systems which provide backflow protection consistent with the level of risk associated with the plumbing fixture fitting ...ASME A112.18.6
Abstract: This Standard covers flexible water connectors for use in water supply systems under
(a) continuous pressure in accessible locations; and
(b) intermittent pressure in recreational vehicles only.
In this Standard, ...