درباره ما
Search
CSV
RISASME B16.4 INTERPRETATIONS: Interpretations to B16.4-1998 - Gray Iron Threaded Fittings - Classes 125 and 250
Abstract: AS a service to persons who use the B16 standards, the B16 Committee renders interpretations of the requirements upon request. The procedure for requesting an interpretation is described in the following paragraphs. ...
ASME PTC 2: Definitions and Values Performance Test Codes
Abstract: OBJECT AND SCOPE
This Code contains standards for terms, units of measure, values of constants, symbols, and technical nomenclature that are to be used in all individual test codes. The implication of the words ...
This Code contains standards for terms, units of measure, values of constants, symbols, and technical nomenclature that are to be used in all individual test codes. The implication of the words ...
ASME MFC-6: Measurement of Fluid Flow in Pipes Using Vortex Flowmeters
Abstract: This Standard
(a) describes the use of vortex flowmeters, including their physical components, principle of operation, installation, performance, influence factors, and calibration in a closed conduit running full for the measurement of volumetric flow rate and volume flow total of single-phase liquids or gases, including vapors such as steam <...
(a) describes the use of vortex flowmeters, including their physical components, principle of operation, installation, performance, influence factors, and calibration in a closed conduit running full for the measurement of volumetric flow rate and volume flow total of single-phase liquids or gases, including vapors such as steam <...
ASME A17.1 HDBK: Safety Code for Elevators and Escalators
Abstract: INTRODUCTION
In 1976 I was appointed to the A17 Editorial Committee with Al Land (Chair), William "Bill" Crager (A17 Chair), and Manuel Gutierrez (ASME Secretary). At the time, the A17 Editorial Committee ...
In 1976 I was appointed to the A17 Editorial Committee with Al Land (Chair), William "Bill" Crager (A17 Chair), and Manuel Gutierrez (ASME Secretary). At the time, the A17 Editorial Committee ...
ASME B20.1: Safety Standard for Conveyors and Related Equipment
Abstract: This Standard applies to the design, construction, installation, maintenance, inspection, and operation of conveyors and conveying systems in relation to hazards. The conveyors may be of the bulk material, package, or ...
ASME B18.21.2M: Lock Washers (Metric Series) - Supersedes IFI 532: 1982
Abstract: This Standard covers the dimensions, physical properties, and methods of testing for helical spring and tooth lock washers.
The inclusion of dimensional data in this Standard is not intended to imply that all products described are stock production items. Consumers should consult with suppliers concerning the availability of products.
NOTE: T...
The inclusion of dimensional data in this Standard is not intended to imply that all products described are stock production items. Consumers should consult with suppliers concerning the availability of products.
NOTE: T...
ASME B30.2 INTERPRETATIONS: Interpretations to B30.2 - Overhead and Gantry Cranes (Top Running Bridge, Single or Multiple Girder, Top Running Trolley Hoist) - Includes Interpretations through January 2010
Abstract: Scope:
This publication includes all of the written replies issued between the indicated dates by the Secretary, speaking for the ASME B30 Committee, Safety Standards for Cableways, ...
This publication includes all of the written replies issued between the indicated dates by the Secretary, speaking for the ASME B30 Committee, Safety Standards for Cableways, ...
ASME Y14.2: Line Conventions and Lettering
Abstract: This Standard establishes the line and lettering practices for use in the preparation of drawings, including the recognition of the requirements for computer aided design (CAD) and manually prepared drawings.
ASME B1 TECH REPT: Measurement Uncertainty for 60 Deg. Screw Thread Gage Element Measurement (Inch and Metric)
Abstract: This Report provides estimates of uncertainty associated with the measurement of pitch diameter, lead and flank angle only for screw thread gages. It is intended that these estimates will be used as a guide to resolve ...