درباره ما
Standard Specification for Nickel-Molybdenum Alloy Rod
ASTM B335-25
Organization:
ASTM - ASTM International
Year: 2025
Abstract: This specification covers rod of nickel-molybdenum alloys of UNS N10001, N10665, N10675, N10629, and N10624 for use in general corrosive service. The material shall conform to the required chemical composition for nickel, molybdenum, iron, chromium, carbon, silicon, cobalt, manganese, phosphorus, sulfur, vanadium, nickel, molybdenum, aluminum, columbium, copper, tantalum, titanium, tungsten, zirconium, and magnesium. The alloys shall conform to the required mechanical properties such as tensile strength, yield strength, elongation, and Rockwell hardness.
Collections
:
-
Statistics
Standard Specification for Nickel-Molybdenum Alloy Rod
Show full item record
| contributor author | ASTM - ASTM International | |
| date accessioned | 2025-09-30T19:30:14Z | |
| date available | 2025-09-30T19:30:14Z | |
| date copyright | 2025 | |
| date issued | 2025 | |
| identifier other | b0335-25.pdf | |
| identifier uri | http://yse.yabesh.ir/std/handle/yse/343955 | |
| description abstract | This specification covers rod of nickel-molybdenum alloys of UNS N10001, N10665, N10675, N10629, and N10624 for use in general corrosive service. The material shall conform to the required chemical composition for nickel, molybdenum, iron, chromium, carbon, silicon, cobalt, manganese, phosphorus, sulfur, vanadium, nickel, molybdenum, aluminum, columbium, copper, tantalum, titanium, tungsten, zirconium, and magnesium. The alloys shall conform to the required mechanical properties such as tensile strength, yield strength, elongation, and Rockwell hardness. | |
| language | English | |
| title | Standard Specification for Nickel-Molybdenum Alloy Rod | en |
| title | ASTM B335-25 | num |
| type | standard | |
| status | Active | |
| tree | ASTM - ASTM International:;2025 | |
| contenttype | fulltext | |
| scope | 1.1 This specification2 covers rod of nickel-molybdenum alloys (UNS N10001, N10665, N10675, N10629, and N10624)3 as shown in Table 1, for use in general corrosive service. 1.2 The following products are covered under this specification: 1.2.1 Rods 5/16 in. to 3/4 in. (7.94 mm to 19.05 mm) excl in diameter, hot or cold finished, solution annealed and pickled or mechanically descaled. 1.2.2 Rods 3/4 in. to 31/2 in. (19.05 mm to 88.9 mm) incl in diameter, hot or cold finished, solution annealed, ground or turned. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. | |
| identifier DOI | 10.1520/B0335-25 |