درباره ما
ASME - ASME International: Recent submissions
Now showing items 161-180 of 1083
-
ASME A112.4.4
Abstract: This Standard covers reversible push-fit drain, waste, and vent (DWV) fittings intended for quick assembly of IPS Schedule 40 series PVC and ABS DWV plastic pipe and fittings for applications above- and belowground at ... -
ASME STP-PT-085
Abstract: BACKGROUND AND INTRODUCTION Steel piping, valves, blow-out preventers (BOPs), and other processing components require protection from contact with hydrogen sulfide-laden oil or gas. These “sour” products are ... -
ASME A112.14.3
Abstract: This Standard covers general product requirements as well as the performance criteria for the testing and rating of hydromechanical grease interceptors, rated by flow in gallons per minute (gpm) or liters per minute (L/min). -
ASME A112.18.6
Abstract: This Standard covers flexible water connectors for use in water supply systems under (a) continuous pressure in accessible locations; and (b) intermittent pressure in recreational vehicles only. In this Standard, "shall" ... -
ASME Y14.5.2
Abstract: This Standard establishes certification requirements for a geometric dimensioning and tolerancing professional (GDTP). Certification shall be based on either ASME Y14.5M-1994 or ASME Y14.5-2009, its appendices, and the ... -
ASME RA-S-1.3
Abstract: PURPOSE AND SCOPE Consequence analysis assesses the effect of releases of radionuclides on the surrounding population and the environment. This Standard only includes limited treatment of the impact on doses of the release ... -
ASME STP-PT-082
Abstract: INTRODUCTION ASME ST-LLC request-for-proposal RFP-16-03 (project STIN-0151) sought the calculation of stress intensity K factors for external surface cracks in thick-walled cylinder vessels. The 1040 crack analysis cases ... -
ASME B16.47
Abstract: General This Standard covers pressure–temperature ratings, materials, dimensions, tolerances, marking, and testing for pipe flanges in sizes NPS 26 through NPS 60. Included are flanges with rating class designations ... -
ASME STP-PT-081
Abstract: INTRODUCTION AND DESCRIPTION OF THE PROBLEM Cyclic stress-strain curves describe the stress-strain behavior under cyclic loads. Usually, the cyclic stress amplitude Δσ/2 is plotted as a function of the cyclic ... -
-
ASME A112.19.5
Abstract: This Standard covers spuds and flush valves for water closet bowls, tanks, and urinals. In this Standard, “shall” is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order ... -
ASME B16.18
Abstract: This Standard for cast copper alloy solder joint pressure fittings designed for use with copper water tube establishes requirements for (a) pressure–temperature ratings (b) abbreviations for end connections (c) sizes ... -
ASME STP-PT-077
Abstract: FOREWORD This publication was prepared by ASME ST-LLC and sponsored by ASME and EPRI. The project was conducted by EPRI under a cost-sharing agreement with ASME ST-LLC. Longitudinal seam-welded, high-temperature piping, ... -
ASME B30.29
Abstract: The ASME B30 Standard contains provisions that apply to the construction, installation, operation, inspection, testing, maintenance, and use of cranes and other lifting and material-movement-related equipment. For the ... -
ASME A112.4.14
Abstract: This Standard specifies requirements for manually operated valves, also known as supply line stops, in sizes NPS 4 and smaller. Valves covered by this Standard are intended for a) installation as water shutoff valves ... -
ASME HST-3
Abstract: (a) This Standard establishes performance requirements for chain, wire rope, and web strap lever hoists for lifting, pulling, and tensioning applications (see Figures 3-0.1-1, 3-0.1-2, ... -
ASME B30.13
Abstract: SCOPE EXCLUSIONS Any exclusion of, or limitations applicable to the equipment, requirements, recommendations or operations contained in this Standard are established in the affected volume’s scope. PURPOSE The B30 ... -
ASME STP-NU-083
Abstract: INTRODUCTION Considering the properties of prestressing steel and the level of compression in concrete, prestressed concrete members should respond with lower deflections under blast loading than similarly-sized, conventionally ... -
ASME B30.9
Abstract: SCOPE OF ASME B30.9 Volume B30.9 includes provisions that apply to the fabrication, attachment, use, inspection, testing, and maintenance of slings used for load-handling purposes, used in conjunction with equipment described ... -
ASME A112.19.10
Abstract: This Standard establishes physical, material, testing, and marking requirements for retrofit dual flush devices that are installed within gravity-type water closet tanks and have a full flush volume of 4.8 Lpf (1.28 gpf) ...