درباره ما
DIN - Deutsches Institut für Normung e. V.: Recent submissions
Now showing items 181-200 of 22183
-
DIN EN ISO 18278-2
Abstract: Scope: This part of ISO 18278 provides specific test procedures for the determination of the acceptable welding current range and the electrode life. It is applicable for the evaluation of the weldability of assemblies of ... -
DVS 2207-5
Abstract: Scope: This Technical Code applies to the PE-HD welding of factory made, thermal insulated and directly buried pipes for district heating networks in accordance with AGFW FW 401, EN 253, EN 448, EN 488, EN 489, EN 13941, ... -
DIN EN 845-3
Abstract: Scope: This European Standard specifies the requirements for masonry bed joint reinforcement for structural use (see 5.2.1) and for non-structural use (see 5.2.2). Where products are intended for use in cavity wall ... -
DIN EN ISO 105-X16
Abstract: Scope: This part of ISO 105 specifies a method for determining the resistance of the colour of textiles to rubbing off and staining other materials where the singling out of areas smaller than possible to test with the ... -
DIN ISO 18898
Abstract: Scope: This International Standard specifies procedures for the calibration and verification of durometers of types A, D, AO and AM (see ISO 7619-1), IRHD pocket meters (see ISO 7619-2), IRHD dead-load instruments (see ISO ... -
DIN EN ISO 18541-1
Abstract: Scope: This part of ISO 18541 provides a general overview and structure of each part of ISO 18541. It also specifies use cases related to repair and maintenance information (RMI) systems in order to standardize the access ... -
DIN EN ISO 11702
Abstract: Scope: This International Standard specifies a method for the quantitative determination of the total sterols content by means of an enzymatic staining test. The method is applicable to free and esterified sterols in animal ... -
DIN EN 12697-17
Abstract: Scope: This European Standard specifies a test method for determining the particle loss of porous asphalt mixtures. Particle loss is assessed by the loss of mass of porous asphalt samples after turns in the Los Angeles ... -
LN 668
Abstract: Scope: This standard is applicable to bright round steel of 2 mm to 200 mm diameter made from the material specified in Table 4. -
-
-
DIN EN ISO 2179
Abstract: Scope: Scope and field of application This International Standard specifies requirements for electroplated coatings of the intermetallic compound SnNi, with a composition of approximately 65 % (m/m) tin and 35 % (m/m) ... -
DIN EN ISO 15148
Abstract: Scope: This European Standard specifies a method for determining, by partial immersion with no temperature gradient, the short-term liquid water absorption coefficient. It is intended to assess the rate of absorption of ... -
DIN EN 12735-1
Abstract: Scope: This European Standard specifies the requirements, sampling, test methods and conditions of delivery for seamless round copper and copper alloy tubes used for refrigeration and air-conditioning piping systems (i.e. ... -
DIN EN 16508
Abstract: Scope: This European Standard specifies performance requirements and design methods for temporary roofs and encapsulations. It is possible to form the constructions in several ways — temporary roof which is ... -
DIN EN 1839
Abstract: Scope: This European Standard specifies two test methods (method T and method B) to determine the explosion limits of gases, vapours and their mixtures, mixed with air or an air / inert gas mixture (volume fraction of the ... -
-
DIN EN ISO 24490
Abstract: Scope: This International Standard specifies the minimum requirements for the design, manufacture and testing of pumps for cryogenic service. This International Standard is applicable to centrifugal pumps. However, it can ... -
DIN EN 13592
Abstract: Scope: This European Standard specifies the general characteristics, test methods and requirements for sacks, bags and bin liners, made from plastic films, used for household waste collection, or household selective waste ... -
DIN EN ISO 636
Abstract: Scope: This International Standard specifies requirements for classification of rods and wires in the aswelded condition and in the post-weld heat-treated condition for tungsten inert gas welding of nonalloy and fine-grain ...