درباره ما
ECIA - Electronic Components Industry Association: Recent submissions
Now showing items 481-500 of 507
-
ECA 513
Abstract: This standard applies to armature-type, circuit-board-mounted relays permitting board center spacings of less than 1 inch. These relays generally are classed in the load range of 0 to 2 amperes. This document is ... -
ECA 540HAAA
Abstract: The ball grid array (BGA) burn-in sockets of assessed quality covered by this Detail Specification have:
— Maximum enclosure dimensions as shown in figure 2.
— A working voltage not exceeding 250 volts ... -
ECA EIA-364-14B
Abstract: This standard establishes a test method to assess the ability of connectors to withstand the effects of controlled amounts of ozone and still maintain effective environmental protection.
CAUTION — Since ozone is ... -
ECA TEP 167
Abstract: This test method applies to the measurement of x-radiation emitted from high voltage rectifiers and shunt regulators.
Purpose To obtain the soft x-radiation characteristics of high voltage receiving tubes in ... -
ECA 208
Abstract: SCOPE AND MEANINGS
Definition and register of all forms of printed wiring are included. "Definition" is the degree of faithfulness of reproduction of conductor referred to the Master Pattern. "Register" ... -
ECA 483
Abstract: This method provides procedures for the measurement of effective series resistance (esr) and capacitance of multilayer ceramic capacitors from frequencies of 25 MHz to 1.25 GHz. A series connection permits the measurement ... -
ECA 186-1E
Abstract: PURPOSE
This test is intended to evaluate the effect of absorption and diffusion of moisture and moisture vapor on component parts. The test in an artificial environmental test, accelerated to shorten ... -
ECA EIA/ECA-720-A
Abstract: This standard defines the dimensions and connector locations of 63.5 millimeters (2.5 inch) small form factor disk drives.
The purpose of this standard is to define the external characteristics of small from factor ... -
ECA EIA-364-13E
Abstract: This standard establishes a method to determine the forces required to mate and unmate electrical connectors or protective caps with connectors, connectors/sockets with gages or devices. Unless otherwise specified in the ... -
ECA EIA-540FAAC
Abstract: The Multi-Package Module Sockets of assessed quality covered by this Detail Specification shall have:
a) Maximum enclosure dimensions (See Figure 1.)
b) Working voltage not to exceed 250 volt (rms).
c) Current ... -
ECA EIA-364-17C
Abstract: This standard establishes a test method to determine the ability of an electrical connector and sockets to withstand elevated temperatures with or without electrical loading.
Atmospheric pressure
This procedure for ... -
ECA EIA-364-27C
Abstract: This test procedure establishes a test method to assess the ability of electrical components to withstand specified severities of mechanical shock. -
ECA RS-406
Abstract: This document defines the recommended requirements for multi-contact electric connectors for the purpose of adapting electric conductors to printed-wiring boards, and for the purpose of interconnecting one printed-wiring ... -
ECA IS-43AJ
Abstract: This Detail Specification defines Type 9 Plenum cable used with the Token Ring LAN Cabling System. Type 9 P consists of 2 twisted pairs of Data Grade Media (DGM) shielded with aluminum tape and braided shields, all cabled ... -
ECA IS-43AG
Abstract: This Detail Specification defines Type 6 Office cable used with the Token Ring LAN Cabling System. Type 6 consists of 2 twisted pairs of Data Grade Media (DGM) constructed of flexible stranded conductors, shielded with ... -
ECA EIA-364-58A
Abstract: This standard establishes test methods to determine the ability of the contact retention system in an electrical connector with removable contacts to withstand a static mechanical load at elevated temperature. -
ECA EIA-944
Abstract: Description
This specification defines the qualification program for surface mount ferrite chip beads. The qualification program is defined in Table 1. Specification sheets can be added, as required, ... -
ECA EIA-364-01B
Abstract: This standard establishes test methods to determine the ability of an electrical connector and sockets to withstand a specified acceleration force without damage detrimental to its specified performance. -
ECA 456-A
Abstract: This standard describes the requirements for metallized electrode film dielectric capacitors, dry or Non-PCB liquid filled, and sealed in metal cases or in non-metal cases made of self-extinguishing material. They are ...