درباره ما
ECIA - Electronic Components Industry Association: Recent submissions
Now showing items 461-480 of 507
-
ECA 512-1
Abstract: This guide is intended to supplement EU-512, "Standard Methods of Measurement of Equivalent Electrical Parameters of Quartz Crystal Units, 1 kHz to 1 gHz." Frequent mention of the standard is made, and having the standard ... -
ECA 217-A
Abstract: GENERAL
The cores covered by this standard are intended for use in the construction of transformers and inductors, They are wound tape cores bonded with a varnish or resin material and cut into sections ... -
ECA EIA-364-1004
Abstract: This standard describes recommended test sequences for verifying the specified current rating of freestanding contacts or electrical connectors and sockets used in power applications. These sequences may be used to qualify ... -
ECA 540H000
Abstract: This sectional specification relates to the burn-in sockets for Ball Grid Array (BGA) devices of assessed quality. The purpose of this specification is to provide a means of interchangeability between qualified devices and ... -
ECA 206-C
Abstract: PURPOSE AND SCOPE
It is the purpose of this Standard to establish the basic rules, which shall be used as a guide in the preparation of basing and terminal diagrams for electron tubes and associated ... -
ECA 700A0AD
Abstract: This specification covers rectangular self-locking connectors with ribbon style (leaf spring) connector contacts on 1.27 mm (0.050 in) contact spacing. Connector polarization is achieved by the trapezoidal configuration ... -
ECA EIA-540DBAA
Abstract: The decoupling capacitor dual in-line sockets of assessed quality covered by this Detail Specification shall have:
a) Maximum enclosure dimensions (See Figure 1 and Table 1 I.
b) Working voltage not to exceed 250 ... -
ECA CB 2
Abstract: ABSTRACT
Contamination of printed wiring boards is defined, and examples are given of the causes of such contamination. The electrical effects of such contamination are then reviewed. Specifications are given ... -
ECA EIA/ECA-676-A
Abstract: This specification defines the configuration characteristics associated with the 78 millimeter x 54 millimeter (1.8 inch) form factor drive that has a parallel interface and operates at 3.3V.
The purpose is to define ... -
ECA EIA-5400000-A
Abstract: This generic specification applies to electromechanical sockets of assessed quality for use in direct current, analog, and digital applications. This generic specification shall be used in conjunction with the basic ... -
ECA EIA-364-42C
Abstract: This standard establishes a method to determine the effects of impacts on electrical connectors.
Object
The object of this test procedure is to determine the ability of a connector to withstand impacts of the type ... -
ECA EIA-501-A
Abstract: This test method applies to the measurement of x-radiation emitted from raster-scanned dired-view data cathode-ray tubes. For some applications the test procedures described in EIA-503 "Recommended Practice for Measurement ... -
ECA IS-43AH
Abstract: This Detail Specification defines Type 8 Undercarpet cable used with the Token Ring LAN Cabling System. Type 8 cable consists of 2 parallel pairs of data grade wires shielded with copper foil, all cabled into a single, ... -
ECA RS-380-A
Abstract: This Standard is intended to be a guide to the selection of contact dimensions and tolerances in the early design phase of an electrical connector.
The dimensions and tolerances established in this document are intended ... -
ECA 700AOAE
Abstract: This Standard applies to a family of connectors having the following characteristics:
• unshielded,
• trapezoidal-shaped mating interface,
• 1.27 mm pitch spacing of contacts on a double row, ... -
ECA 700A0AB
Abstract: Scope and Purpose
This specification covers interconnect systems typically used for memory card type devices, specified in PCMCIA PC Card Standard or JEIDA IC Memory Card Guidelines. The contacts are ... -
ECA TEB 25
Abstract: Introduction
Information density in displays in increasing rapidly with the phenomenal growth of data and graphics displays. The introduction of color to data and avionics displays has required ... -
ECA EIA/ECA-887-A
Abstract: Introduction
This specification defines the requirements for a family of thin film resistor networks on silicon with various configurations, packaged in a molded, JEDEC-approved package. -
ECA 256-A
Abstract: PURPOSE
To define the limit for deflected beam clearance in 70° cathode-ray picture tubes by means of a standard deflecting yoke.