Defence Standards: Recent submissions

Now showing items 561-580 of 43216

    • MIL-PRF-11430F 

      Type: standard
      Source: ARMY - GL - U.S. Army Natick Soldier Research, Development & Engineering Center:;1997
      Organization : ARMY - GL - U.S. Army Natick Soldier Research, Development & Engineering Center
      Abstract: This specification covers the performance and acceptance requirements for an insulated case for the 5-gallon military water can (see 6.1). Intended Use: The insulated case is primarily for use in cold ...
      Subject(s) : Cold retention , Container insulating , Heat retention ,

    • W-C-596/139B VALID NOTICE 2 

      Type: standard
      Source: DLA - CC - DLA Land and Maritime:;2011
      Organization : DLA - CC - DLA Land and Maritime

    • MIL-I-3158D VALID NOTICE 1 

      Type: standard
      Source: NAVY - SH - Naval Sea Systems Command (Ship Systems):;1988
      Organization : NAVY - SH - Naval Sea Systems Command (Ship Systems)

    • MIL-DTL-45449C (1) 

      Type: standard
      Source: ARMY - AR - US Army Research Devlp & Engr Command, Armament Research Devlp & Engr Center:;2012
      Organization : ARMY - AR - US Army Research Devlp & Engr Command, Armament Research Devlp & Engr Center
      Abstract: This specification covers requirements and provisions for the manufacturing and assembly of wood pallet units for use in shipment of projectile metal parts and projectile ammunition.Intended Use: This ...

    • A-A-59769A 

      Type: standard
      Source: DLA - CC - DLA Land and Maritime:;2013
      Organization : DLA - CC - DLA Land and Maritime
      Abstract: This commercial item description (CID) covers the general requirements for a resistor network, ball grid array terminator. These resistors networks provide series and parallel termination between the source and the receiver. ...

    • A-A-59438 VALID NOTICE 1 

      Type: standard
      Source: DLA - CC - DLA Land and Maritime:;2004
      Organization : DLA - CC - DLA Land and Maritime

    • SMD-5962-90749 REV B 

      Type: standard
      Source: DLA - CC - DLA Land and Maritime:;2012
      Organization : DLA - CC - DLA Land and Maritime
      Abstract: This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are ...

    • A-A-59476 VALID NOTICE 2 

      Type: standard
      Source: DLA - GS3 - DLA Aviation - Richmond:;2011
      Organization : DLA - GS3 - DLA Aviation - Richmond

    • MIL-R-81839 

      Type: standard
      Source: NAVY - AS - Naval Air Systems Command:;1977
      Organization : NAVY - AS - Naval Air Systems Command
      Abstract: This specification establishes the requirements for the manufacture and inspection of one type of bomb rack capable of carrying and releasing 22.68 kilogram (50 pound) to 657.71 kilogram (1,450 pound) stores having suspension ...

    • MIL-DTL-32260 VALID NOTICE 1 

      Type: standard
      Source: ARMY - AR - US Army Research Devlp & Engr Command, Armament Research Devlp & Engr Center:;2013
      Organization : ARMY - AR - US Army Research Devlp & Engr Command, Armament Research Devlp & Engr Center

    • MIL-DTL-11484/50G 

      Type: standard
      Source: ARMY - IH - Institute of Heraldry:;2005
      Organization : ARMY - IH - Institute of Heraldry

    • MIL-V-2961D 

      Type: standard
      Source: NAVY - SH - Naval Sea Systems Command (Ship Systems):;1990
      Organization : NAVY - SH - Naval Sea Systems Command (Ship Systems)
      Abstract: This specification covers self-contained globe (in-line and offset) pressure reducing valves for gas (air or nitrogen) service intended for shipboard and marine environment use (see 6.1). Guidance in the selection ...
      Subject(s) : Air systems , Dome , In-line , Nitrogen systems , Offset , Pilot , Poppet , Spring ,

    • MIL-DTL-41819/40C 

      Type: standard
      Source: ARMY - IH - Institute of Heraldry:;1997
      Organization : ARMY - IH - Institute of Heraldry

    • NACA-TN-2288 

      Type: standard
      Source: NASA - National Aeronautics and Space Administration (NASA):;1951
      Organization : NASA - National Aeronautics and Space Administration (NASA)
      Abstract: Comparisons of the low-Speed experimental lift and hinge-moment parameters of flapped lifting surfaces with and without sweepback with values computed by several theoretical procedures are presented. Based on these limited ...
      Subject(s) : AIRFOILS , BALANCED , CHARACTERISTICS , DISTRIBUTION , ELEVATORS , FLAPS , GAP , HINGE , HORIZONTAL , LIFT , LIFTING , MOMENTS , NACA , SEALED , SPAN , SURFACE , SURFACES , SWEPTBACK , TAIL , THEORIES , WING ,

    • MIL-DTL-11589/441 

      Type: standard
      Source: ARMY - IH - Institute of Heraldry:;1995
      Organization : ARMY - IH - Institute of Heraldry
      Abstract: This specification is approved for use by all Departments and Agencies of the Department of Defense
      The requirements for acquiring the product described herein shall consist of this specification sheet and the issue ...

    • MIL-M-28787/324 CANC NOTICE 2 

      Type: standard
      Source: NAVY - SH - Naval Sea Systems Command (Ship Systems):;2013
      Organization : NAVY - SH - Naval Sea Systems Command (Ship Systems)

    • MIL-M-28787/337A CANC NOTICE 2 

      Type: standard
      Source: NAVY - SH - Naval Sea Systems Command (Ship Systems):;2013
      Organization : NAVY - SH - Naval Sea Systems Command (Ship Systems)

    • COMDTINST 5305.8 

      Type: standard
      Source: USCG - United States Coast Guard:;1998
      Organization : USCG - United States Coast Guard

    • MIL-T-81556A (1) 

      Type: standard
      Source: NAVY - AS - Naval Air Systems Command:;1996
      Organization : NAVY - AS - Naval Air Systems Command

    • MIL-R-81367 (1) 

      Type: standard
      Source: NAVY - AS - Naval Air Systems Command:;1974
      Organization : NAVY - AS - Naval Air Systems Command