درباره ما
API - American Petroleum Institute: Recent submissions
Now showing items 1141-1160 of 1822
-
API TR 405
Abstract: FOREWORD
API PUBLICATIONS NECESSARILY ADDRESS PROBLEMS OF A GENERAL NATURE. WITH RESPECT TO PARTICULAR CIRCUMSTANCES, LOCAL, STATE, AND FEDERAL LAWS AND REGULATIONS SHOULD BE REVIEWED.
API IS NOT ... -
API SPEC 17J ERTA
Abstract: This part of ISO 13628 defines the technical requirements for safe, dimensionally and functionally interchangeable flexible pipes that are designed and manufactured to uniform standards and criteria. Minimum requirements ... -
API MPMS 5.8
Abstract: General
This document defines the application criteria for UFMs and addresses the appropriate considerations regarding the liquids to be measured. This document addresses the installation, operation, ... -
API RP 756
Abstract: General
This Recommended Practice (RP) provides guidance for managing the risk from explosions, fires and toxic material releases to on-site personnel located in tents. The term "tent" is used to ... -
API PUBL 4627
Abstract: FOREWORD
API PUBLICATIONS NECESSARILY ADDRESS PROBLEMS OF A GENERAL NATURE. WITH RESPECT TO PARTICULAR CIRCUMSTANCES, LOCAL, STATE, AND FEDERAL LAWS AND REGULATIONS SHOULD BE REVIEWED.
API IS NOT ... -
API STD 2RD
Abstract: This standard addresses riser systems that are part of a floating production system (FPS). Guidelines for design, construction, installation, operation and maintenance of floating production systems (FPSs) are in API 2FPS. ... -
API PUBL 4558
Abstract: 1.1 SCOPE AND PURPOSE
Selecting appropriate oil spill protection, recovery, and cleanup techniques, before and following an oil spill, is a critical element affecting the ultimate environmental impact and cost ... -
API PUBL 4677
Abstract: Scope:
This project develops a set of emission factor tables that can be used to replace the AP-42 emission factor for refinery process drains. The project also develops a two-phase ... -
API STD 530
Abstract: This standard specifies the requirements and gives recommendations for the procedures and design criteria used for calculating the required wall thickness of new tubes and associated component fittings for fired heaters ... -
API RP 2SM
Abstract: This document applies to synthetic fiber ropes used in the form of taut leg or catenary moorings for both permanent and temporary offshore installations such as:
a) monohull-based floating production, storage, and ... -
API RP 17O
Abstract: This recommended practice (RP) addresses the requirements for the use of high integrity pressure protection systems (HIPPS) for subsea applications. API 14C, IEC 61508, and IEC 61511 specify the requirements for onshore, ... -
API BULL 2INT-DG
Abstract: PREFACE
Hurricane Ivan in 2004 and hurricanes Katrina and Rita in 2005 resulted in considerable damage and destruction to fixed and floating facilities in the Gulf of Mexico (GOM). Several API Committees ... -
API SPEC 12J
Abstract: General
This specification covers minimum requirements for the design, fabrication, and shop testing of oil-field type oil and gas separators and/or oil-gas-water separators used in the production of ... -
API MPMS 3.6
Abstract: This standard covers selection, installation, commissioning, calibration and verification of Hybrid Tank Measurement Systems (HTMSs) for the measurement of level, static mass, observed and standard volume, and observed and ... -
API VOCATIONAL BOOK 3
Abstract: FOREWORD
The underground injection of water, whether into waterfloods or disposal systems, is an integral portion of the cost of producing oil. The magnitude of this cost has increased because more water is being ... -
API STD 6DX
Abstract: This International Standard defines the requirements for mechanical integrity and sizing of actuators used on valves manufactured under ISO 14313 and API Specification 6D.
This International Standard is applicable to ... -
API PUBL 4655
Abstract: FOREWORD
API PUBLICATIONS NECESSARILY ADDRESS PROBLEMS OF A GENERAL NATURE. WITH RESPECT TO PARTICULAR CIRCUMSTANCES, LOCAL, STATE, AND FEDERAL LAWS AND REGULATIONS SHOULD BE REVIEWED.
API IS NOT ... -
API SPEC 11AX
Abstract: This specification provides the requirements and guidelines for the design of subsurface sucker rod pumps and their components as defined herein for use in the sucker rod lift method for the petroleum and natural gas ...