درباره ما
API - American Petroleum Institute: Recent submissions
Now showing items 1461-1480 of 1822
-
API BULL 97
Abstract: This bulletin provides guidance on information that is to be shared regarding well construction and rigspecific operating guidelines. It is intended to align the lease operator's safety and environmental management system ... -
API PUBL 4720
Abstract: Both the U.S. Environmental Protection Agency (EPA) and the American Petroleum Institute (API) have published toxic air pollutant emission factors for combustion sources. These emission factors are frequently used by ... -
API SPEC 17K
Abstract: Purpose
This part of ISO 13628 defines the technical requirements for safe, dimensionally and functionally interchangeable bonded flexible pipes that are designed and manufactured to uniform standards ... -
API PUBL 341
Abstract: FOREWORD
API PUBLICATIONS NECESSARILY ADDRESS PROBLEMS OF A GENERAL NATURE. WITH RESPECT TO PARTICULAR CIRCUMSTANCES, LOCAL, STATE, AND FEDERAL LAWS AND REGULATIONS SHOULD BE REVIEWED.
API IS NOT ... -
API STD 520 PT I
Abstract: This standard applies to the sizing and selection of pressure-relief devices used in refineries, chemical facilities, and related industries for equipment that has a maximum allowable working pressure (MAWP) of 15 psig ... -
API SPEC 15HR ERTA 1
Abstract: Scope
PURPOSE
This specification was formulated to provide for the availability of safe, dimensionally and functionally interchangeable high pressure fiberglass line pipe with a Specification 15HR ... -
API SPEC 19G3
Abstract: This part of ISO 17078 provides requirements and guidelines for running tools, pulling tools, kick-over tools and latches used for the installation and retrieval of flow control and other devices to be installed in side-pocket ... -
API PUBL 311
Abstract: FOREWORD
API PUBLICATIONS NECESSARILY ADDRESS PROBLEMS OF A GENERAL NATURE. WITH RESPECT TO PARTICULAR CIRCUMSTANCES, LOCAL, STATE, AND FEDERAL LAWS AND REGULATIONS SHOULD BE REVIEWED.
API IS NOT ... -
API PUBL 4640
Abstract: Scope:
Research on the fate and effects of spilled petroleum products has traditionally focused on estuarine and marine ecosystems. The perception of these habitats as being at ... -
API RP 11S3
Abstract: This recommended practice covers the installation and replacement of all major components that comprise a typical, electrical submersible pumping system. (See Figure 1.) Specifically, it covers installations in oil and gas ... -
API HF3
Abstract: The purpose of this guidance document is to identify and describe practices currently used in the oil and natural gas industry to minimize surface environmental impacts—potential impacts on surface water, soils, ... -
API STD 620
Abstract: General
The API Downstream Segment has prepared this standard to cover large, field-assembled storage tanks of the type described in 1.2 that contain petroleum intermediates (gases or vapors) and ... -
API MPMS TR 2570
Abstract: This technical report will provide guidance for the application, installation, operation, verification, and proving of OWDs for use in the non-custody transfer measurement of water in crude oil and condensate. -
API PUBL 4711
Abstract: Scope:
This manual describes methods used to obtain input parameters for models that evaluate the mobility and potential recovery of petroleum liquids in unconsolidated granular ... -
API RP 7HU1
Abstract: General
This recommended practice (RP) sets forth procedural recommendations as well as an engineering solution to the mismatching of a female 2-inch Figure 402, a female 2-inch Figure 602, or a female ... -
API TR 406
Abstract: FOREWORD
API PUBLICATIONS NECESSARILY ADDRESS PROBLEMS OF A GENERAL NATURE. WITH RESPECT TO PARTICULAR CIRCUMSTANCES, LOCAL, STATE, AND FEDERAL LAWS AND REGULATIONS SHOULD BE REVIEWED.
API IS NOT ... -
API DR 351
Abstract: FOREWORD
API PUBLICATIONS NECESSARILY ADDRESS PROBLEMS OF A GENERAL NATURE. WITH RESPECT TO PARTICULAR CIRCUMSTANCES, LOCAL, STATE, AND FEDERAL LAWS AND REGULATIONS SHOULD BE REVIEWED.
API IS NOT ... -
API STD 2555
Abstract: This standard describes the procedure for calibrating tanks, or portions of tanks, larger than a barrel or drum by introducing or withdrawing measured quantities of liquid.