درباره ما
API - American Petroleum Institute: Recent submissions
Now showing items 1621-1640 of 1822
-
API TR 6F1
Abstract: 1 Scope and Applicability
The sizes of interest are shown in Table 1. The ANSI (8) sizes are adopted by API Spec 6D. The API sizes refer to those in API Spec 6A.
Table 2 shows the materials and gasket ... -
API TR 942-A
Abstract: The American Petroleum Institute (API) Committee on Refinery Equipment, Subcommittee on Corrosion and Materials undertook a project to develop this technical report on materials, fabrication, and repair issues related to ... -
API TR 11L6
Abstract: This technical report covers polyphase, squirrel-cage, induction motors for use as the prime mover for beam pumping units (size range of 200 HP and below). It includes a user Motor Data Sheet (Annex A) and an Electric Motor ... -
API STD 20C
Abstract: This API standard specifies requirements for the qualification and production of closed die forgings for use in API service components in the petroleum and natural gas industries when referenced by an applicable equipment ... -
API SPEC 17D
Abstract: This part of ISO 13628 provides specifications for subsea wellheads, mudline wellheads, drill-through mudline wellheads and both vertical and horizontal subsea trees. It specifies the associated tooling necessary to handle, ... -
API RP 1171
Abstract: This recommended practice (RP) applies to natural gas storage in depleted oil and gas reservoirs and aquifer reservoirs, and focuses on storage well, reservoir, and fluid management for functional integrity in design, ... -
API BULL 2V
Abstract: Bulletin 2V provides guidance for the design of steel flat plate structures. These often constitute main components of offshore structures. When applied to Tension Leg Platforms (TLPs) this Bulletin should be viewed ... -
API PUBL 1593
Abstract: FOREWORD
The contents of this paper are for the purpose of study and discussion of government legislative or regulatory proposals and do not necessarily represent the view of the American Petroleum Institute or ... -
API MPMS 8.3 ERTA
Abstract: This standard covers the handling, mixing, and conditioning procedures required to ensure that a representative sample of the liquid petroleum or petroleum product is delivered from the primary sample container/receiver ... -
API RP 11S2
Abstract: GENERAL
This recommended practice provides guidelines and procedures covering electric submersible pump performance testing intended to establish product consistency. These recommended practices are ... -
API TR 412
Abstract: FOREWORD
API PUBLICATIONS NECESSARILY ADDRESS PROBLEMS OF A GENERAL NATURE. WITH RESPECT TO PARTICULAR CIRCUMSTANCES, LOCAL, STATE, AND FEDERAL LAWS AND REGULATIONS SHOULD BE REVIEWED.
API IS NOT ... -
API PUBL 4686
Abstract: FOREWORD: This 1999 International Oil Spill Conference is the 16th biennial event since the first conference held in December 1969. The conference is sponsored jointly by the following:
American Petroleum ... -
API TR 10TR2
Abstract: Introduction
A flawless cementation of the casing strings is fundamental not only for safety reasons, but also to keep drilling and production costs at a minimum level.
A cement job has to fulfill ... -
API MPMS 2.2E ERTA
Abstract: This part of ISO 12917 specifies manual methods for the calibration of nominally horizontal cylindrical tanks, installed at a fixed location. It is applicable to horizontal tanks up to 4 m in diameter and 30 m in length. ... -
API TR 2575
Abstract: This technical report presents a method to compute the density, compressibility factor, and supercompressibility factor for thermally cracked gas (TCG) for custody transfer using orifice meters. It provides equations, ... -
API STD 674
Abstract: This standard covers the minimum requirements for reciprocating positive displacement pumps and pump units for use in the petroleum, petrochemical, and gas industry services. Both direct-acting and power-frame types are ... -
API PUBL 1645
Abstract: Scope:
Stage II vapor recovery is a well-known air quality control measure that reduces ozone precursors from gasoline dispensing facilities (GDFs). As a result of its relative ... -
API MPMS 22.1
Abstract: This document is for the development of testing protocols and to serve as a guideline to document performance characteristics of hydrocarbon fluid measurement related devices. -
API STD 650
Abstract: General
This standard establishes minimum requirements for material, design, fabrication, erection, and inspection for vertical, cylindrical, aboveground, closed- and open-top, welded storage ... -
API RP 1172
Abstract: Construction activities parallel to existing transmission pipelines, for any distance, are the focus of this recommended practice (RP). Activity of concern includes construction activity that could impact an existing ...