درباره ما
IEEE - The Institute of Electrical and Electronics Engineers, Inc.: Recent submissions
Now showing items 1261-1280 of 2832
-
IEEE Standard for Digitizing Waveform Recorders
Abstract: Terminology and test methods for describing the performance of waveform recorders are presented in this standard.Subject(s) : IEEE 1057(TM) , effective number of bits , frequency response , noise , sine fitting , step pulse response , total harmonic distortion , transitions levels , waveform recorders , Distortion , Frequency response , Harmonic anlaysis , IEEE Standards , Noise measurement , Pulse measurements , -
IEEE Recommended Practice for Preferred Ratings for High-Voltage(>1000 volts) AC Circuit Breakers Designated Definite Purpose for Fast Transient Recovery Voltage Rise Times
Abstract: The preferred ratings of transformer-limited fault duty (fast transient recovery voltage rise times) of indoor and outdoor high-voltage circuit breakers rated above 1000 V for use in commercial, industrial, and utility ...Subject(s) : IEEE C37.06.1(TM) , TRV , fast transient recovery voltage rise times , high-voltage circuit breakers , transformer-limited fault , transient recovery voltage , Circuit breakers , High-voltage techniques , IEEE Standards , Power transformers , System recovery , Transient analysis , Voltage control , IEEE standards , circuit breakers , transients , IEEE Std C37.06.1-2017 , fast transient recovery voltage rise times , high-voltage AC circuit breakers , transformer-limited fault duty , -
IEEE Guide for Testing Switchgear Rated Up to 52 kV for Internal Arcing Faults
Abstract: Procedures for testing and evaluating the performance of switchgear for internal arcing faults is covered. A method of identifying the capabilities of this equipment is given. Service conditions, installation, and application ...Subject(s) : IEEE C37.20.7 , accessibility , arc , arc-resistant , bus , compartment , internal arcing fault , medium-voltage controllers , metal-clad switchgear , metal-enclosed bus , metal-enclosed gas-insulated switchgear , metal-enclosed interrupter switchgear , metal-enclosed low-voltage power circuit breaker switchgear , metal-enclosed switchgear , motor control centers , overpressure , protection , switchboard , Arc discharges , Circuit breakers , Fault diagnosis , IEEE Standards , Switchgear , Switching currents , Testing , Voltage control , -
IEEE Standard for Ethernet - Amendment 11: Physical Layer and Management Parameters for Serial 25 Gb/s Ethernet Operation Over Single-Mode Fiber
Abstract: This amendment to IEEE Std 802.3-2015 adds Physical Layer (PHY) specifications and management parameters for 25 Gb/s operation over single-mode fiber at reaches of at least 10 km (25GBASE-LR) and 40 km (25GBASE-ER).Subject(s) : 25 Gb/s Ethernet , 25GBASE-ER , 25GBASE-LR , 25GBASE-SR , Energy Efficient Ethernet (EEE) , Ethernet , Forward Error Correction (FEC) , IEEE 802.3(TM) , IEEE 802.3by(TM) , IEEE 802.3cc(TM) , Physical Coding sublayer (PCS) , Physical Medium Attachment (PMA) sublayer , Physical Medium Dependent (PMD) sublayer , Reconciliation sublayer (RS) , single-mode fiber (SMF) , EPON , Energy efficiency , Ethernet , Forward error correction , IEEE 802.3 Standard , Local area networks , Metropolitan area networks , Physical layer , -
IEEE Standard for Extensions to Standard Test Interface Language (STIL) (IEEE Std 1450-1999) for Test Flow Specification
Abstract: IEEE Std 1450â„¢-1999, which specifies the Standard Test Interface Language (STIL), is extended by this standard to provide an interface between test generation tools and test equipment with regard to the specification of ...Subject(s) : ATPG , ATPRG , CAE , DUT , IC test , IEEE 1450.4(TM) , TPG , automatic test program generator or generation , binning , computer-aided engineering , device under test , integrated circuit test , test flow , test program description , test program language , Automatic testing , Computer aided engineering , IEEE Standards , Integrated circuits , Programming , IEEE standards , automatic test equipment , automatic test software , automatic testing , electronic equipment testing , program testing , IEEE Standard , IEEE Std 1450â„¢-1999 , IEEE Std 1450-1999 , Standard Test Interface Language , Test flow specification , automated test equipment , complete run-time test language , defining flow-related variables , test generation tools , test program components , -
IEEE Standard for Wireless Medium Access Control (MAC) and Physical Layer (PHY) Specifications for Peer Aware Communications (PAC)
Abstract: Physical layer (PHY) and medium access control (MAC) mechanisms are defined in this standard for wireless personal area networks (WPANs) peer aware communications (PAC) optimized for peer-to-peer and infrastructure-less ...Subject(s) : D2D , IEEE 802.15.8(TM) , device-to-device communications , distributed network synchronization , group communications , infrastructure-less , peer aware communications , Device-to-device communication , Distributed processing , IEEE Standards , Media Access Protocol , Physical layer , Synchronization , Wireless networks , IEEE standards , access protocols , peer-to-peer computing , personal area networks , telecommunication signalling , IEEE 802.15.8-2017 , IEEE standard , MAC mechanisms , PAC features , PHY specifications , WPANs , discovery signaling rate , frequency 11 GHz , fully distributed coordination , peer aware communications , peer-to-peer communications , physical layer , scalable data transmission rates , wireless medium access control , wireless personal area networks , -
ISO/IEC/IEEE International Standard -- Information technology -- Telecommunications and information exchange between systems -- Local and metropolitan area networks -- Specific requirements -- Part 1Q: Bridges and bridged networks AMENDMENT 3: Enhancement
Abstract: Enhancements to the forwarding process that supports scheduled traffic is provided in this amendment to IEEE Std 802.1Q-2014.Subject(s) : Bridged Local Area Networks , IEEE 802(R) , IEEE 802.1Q(TM) , IEEE 802.1Qbv(TM) , IEEE 802.1Qca(TM) , IEEE 802.1Qcd(TM) , MAC Bridges , Virtual Bridged Local Area Networks (virtual LANs) , local area networks (LANs) , metropolitan area networks , scheduled traffic , Bridge circuits , IEC Standards , ISO Standards , Local area networks , Media Access Protocol , Metropolitan area networks , Telecommunication traffic , -
IEEE Recommended Practice for the Selection, Field Testing, and Life Expectancy of Molded-Case Circuit Breakers for Industrial Applications
Abstract: A recommended procedure for the selection, application, and determination of the remaining life in molded-case circuit breaker is provided.Subject(s) : IEEE 1458 , available fault values , circuit breaker testing , insulated-case circuit breakers , molded-case circuit breakers , molded-case circuit breakers basics , molded-case circuit breakers life , safety , Circuit breakers , Electrical safety , Fault diagnosis , IEEE Standards , Insulation , Power system reliability , -
IEEE Standard for Information Technology--Portable Operating System Interface (POSIX(R)) Base Specifications, Issue 7
Abstract: POSIX.1-2017 is simultaneously IEEE Std 1003.1(TM)-2017 and The Open Group Standard Base Specifications, Issue 7.POSIX.1-2017 defines a standard operating system interface and environment, including a command interpreter ...Subject(s) : CPU , FIFO , IEEE 1003.1(TM) , X/Open System Interface (XSI) , application program interface (API) , argument , asynchronous , basic regular expression (BRE) , batch job , batch system , built-in utility , byte , child , command language interpreter , extended regular expression (ERE) , file access control mechanism , input/output (I/O) , job control , network , parent , portable operating system interface (POSIX(R)) , shell , stream , string , synchronous , system , thread , Access control , Application programming interfaces , Batch production systems , IEEE Standards , Information technology , Operating systems , Synchronization , Utility programs , -
Health informatics--Personal health device communication - Part 10424: Device Specialization--Sleep Apnoea Breathing Therapy Equipment (SABTE)
Abstract: Within the context of the ISO/IEEE 11073 family of standards for device communication, a normative definition of the communication between sleep apnoea breathing therapy equipment (SABTE) devices (agents) and managers ...Subject(s) : IEEE 11073-10424(TM) , medical device communication , personal health devices , sleep apnoea breathing therapy equipment (SABTE) , Biomedical equipment , Biomedical monitoring , IEEE Standards , Medical devices , Sleep apnea , -
IEEE Standard for the Qualification of Switchgear Assemblies for Class 1E Applications in Nuclear Power Generating Stations
Abstract: The methods and requirements for qualifying switchgear assemblies for indoor areas outside of the containment in nuclear power generating stations are described in this document. These assemblies include: metal-enclosed ...Subject(s) : Class 1E metal-enclosed power switchgear assemblies , DBE , IEEE C37.82(TM) , design basis event , qualified life , Assembly , IEEE Standards , Nuclear power generation , Safety , Switchgear , -
IEEE Standard for Test Methods and Performance Values for Metal-Oxide Varistor Surge Protective Components
Abstract: Test methods and preferred values for metal-oxide varistor (MOV) surge protective components are covered in this standard and have the following main parameter ranges: packaging (leaded disc-type or surface mount), nominal ...Subject(s) : ESD , IEEE C62.33(TM) , MCOV , MOV , TOV , clamping voltage , leaded , metal-oxide varistor , nominal voltage , surface mount , surge current rating , varistor , IEEE Standards , MOSFET circuits , Performance evaluation , Surge protection , Varistors , Voltage control , -
IEEE Standard Design Tests for High-Voltage (>1000 V) Fuses and Accessories Corrigenda 1
Abstract: Corrigenda concerning required procedures for performing design tests for high-voltage fuses are specified. These design tests, are appropriate to expulsion fuses, and cover interrupting tests and fuses using polymeric insulators.Subject(s) : IEEE 37.41(TM) , fuse accessories , fuse design tests , fuse disconnecting switches , fuse-enclosure package (FEP) , high-voltage fuses , Electrical safety , Fuses , High-voltage techniques , IEEE Standards , Switchgear , Voltage control , IEEE standards , electric fuses , polymer insulators , switchgear testing , IEEE Std C37.41-2016-Cor 1-2017 , IEEE standard design testing , accessories corrigenda 1 , high-voltage fuses , interrupting testing , polymeric insulators , -
IEEE Standard for Sensor Performance Parameter Definitions
Abstract: A common framework for sensor performance specification terminology, units, conditions, and limits is provided. Specifically, the accelerometer, magnetometer, gyrometer/gyroscope, accelerometer/magnetometer/gyroscope ...Subject(s) : IEEE 2700(TM) , MEMS , accelerometer , ambient light , barometer , combination sensor , gyroscope , humidity , magnetometer , microelectromechanical , pressure , proximity , sensors systems , temperature , terminology , Accelerometers , Barometers , IEEE Standards , Microelectromechanical systems , Micromechanical devices , Performance evaluation , Sensors , Temperature measurement , -
ISO/IEC/IEEE International Standard - Systems and software engineering - Requirements for acquirers and suppliers of information for users
Abstract: This document was developed to assist users of ISO/IEC/IEEE 15288:2015 or ISO/IEC/IEEE 12207 to acquire or supply information for users as part of the system or life cycle processes. It defines the documentation process ...Subject(s) : IEC Standards , IEEE Standards , ISO Standards , Requirements engineering , Software engineering , Systems engineering and theory , IEC standards , IEEE standards , ISO standards , formal specification , formal verification , information management , software tools , system documentation , systems analysis , Document Plan , ISO/IEC/IEEE 12207 , ISO/IEC/IEEE 15288 , ISO/IEC/IEEE international standard , acquisition plan , document specification , documentation process , information acquirers , information management processes , information suppliers , on-screen documentation , printed documentation , request for proposals , software engineering , software tools , statement of work , systems engineering , user documentation products , user documentation specification , users assistance , -
IEEE Standard Specifications for High-Voltage (>1000 V) Fuses and Accessories
Abstract: Specifications for high voltage (above 1000 volts) Class A and Class B expulsion and current-limiting fuses. This includes: a) Expulsion type Class A [distribution class] fuses, fuse cutouts, fuse disconnecting switches, ...Subject(s) : Class A fuses , Class B fuses , current-limiting fuses , distribution and power class current-limiting fuses , distribution class fuses , distribution fuse cutouts , expulsion fuses , fuse , fuse disconnecting switches , fuse enclosure packages , fuse hooks , fuse links , fuse49 applications , fuses for the protection of shunt capacitors , high-voltage fuses , power class fuses , supports and mountings , tongs , Capacitors , Current limiters , Fuses , High-voltage techniques , IEEE Standards , Power distribution , Voltage control , -
IEEE Standard for Relaxor-Based Single Crystals for Transducer and Actuator Applications
Abstract: The physical and electromechanical requirements for relaxor-based piezoelectric single crystals of lead magnesium niobate-lead titanate (PMN-PT) and lead zinc niobate-lead titanate (PZN-PT) solid solutions of perovskite ...Subject(s) : IEEE 1859(TM) , PMN-PT , PZN-PT , actuators and sensors , crystal compositions , crystal properties and measurements , crystal property specifications , electromechanical transducers , lead magnesium niobate-lead titanate solid solution , lead zinc niobate-lead titanate solid solution , piezoelectric single crystals , Actuators , Crystals , IEEE Standards , Measurement , Sensors , Titanium compounds , Transducers , lead compounds , piezoelectric materials , piezoelectricity , relaxor ferroelectrics , solid solutions , PMN-PbTiO<sub>3</sub> , Pb(Zn<sub>0.33</sub>Nb<sub>0.66</sub>)O<sub>3</sub>-PbTiO<sub>3</sub> , actuator applications , electromechanical properties , electromechanical requirements , lead magnesium niobate-lead titanate , military transducers , multilayer plate devices , perovskite structure , physical properties , physical requirements , piezoelectric single crystals , relaxor-based single crystals , single plates , transducer applications , zinc niobate-lead titanate solid solutions , -
IEEE Standard Requirements for Power-Line Carrier Line Traps (30 kHz to 500 kHz)
Abstract: Line traps inserted into a power line to provide a high impedance at power-line-carrier frequencies (30 kHz to 500 kHz) are covered in this standard. The purpose is to isolate the carrier signal from system impedance changes ...Subject(s) : IEEE C93.3(TM) , PLC , line trap , power line carrier , wave trap , Coolants , Fault diagnosis , IEEE Standards , Impdeance , Inductors , Power transmission lines , Switching systems , IEEE standards , coils , power cables , power inductors , IEEE Std C93.3-2017 , IEEE standard requirements , carrier signal isolation , frequency 30 kHz to 500 kHz , main coil design , power-line carrier line traps , power-line-carrier frequency , single-phase air-cooled inductor , -
IEEE Standard Framework for Prognostics and Health Management of Electronic Systems
Abstract: Information for the implementation of prognostics and health management (PHM) for electronic systems is described in this standard. A normative framework for classifying PHM capability and for planning the development of ...Subject(s) : IEEE 1856(TM) , PHM Metrics , PHM defi nitions , PHM functional model , PHM operational model , classification of electronics , electronic systems , health management , implementation in electronics , prognostics , Classification , IEEE Standards , Medical services , Prognostics and health management , IEEE standards , condition monitoring , electronics industry , product life cycle management , IEEE standard framework , PHM capability , PHM development planning , electronic system , electronic systems , end users , life cycle operations , normative framework , prognostics and health management , -
IEEE Standard for Ethernet - Amendment 10: Media Access Control Parameters, Physical Layers, and Management Parameters for 200 Gb/s and 400 Gb/s Operation
Abstract: Clause 116 through Clause 124 and Annex 119A through Annex 120E are added by this amendment to IEEE Std 802.3-2015. This amendment includes IEEE 802.3 Media Access Control (MAC) parameters, Physical Layer specifications, ...Subject(s) : 200 Gb/s Ethernet , 200GAUI-4 , 200GAUI-8 , 200GBASE-DR4 , 200GBASE-FR4 , 200GBASE-LR4 , 200GBASE-R , 200GMII , 200GXS , 400 Gb/s Ethernet , 400GAUI-16 , 400GAUI-8 , 400GBASE-DR4 , 400GBASE-FR8 , 400GBASE-LR8 , 400GBASE-R , 400GBASE-SR16 , 400GMII , 400GXS , EEE , Energy Efficient Ethernet , Ethernet , FEC , IEEE 802.3(TM) , IEEE 802.3bs(TM) , MMF , PAM4 , PMD , Physical Medium Dependent sublayer , SMF , forward error correction , Energy efficiency , Ethernet , Forward error correction , IEEE Standards , Local area networks , Media Access Protocol , Metropolitan area networks , Physical layer ,