درباره ما
IEEE - The Institute of Electrical and Electronics Engineers, Inc.: Recent submissions
Now showing items 2361-2380 of 2832
-
IEEE 1057
Abstract: Instruments covered by this standard are electronic digitizing waveform recorders, waveform analyzers, and digitizing oscilloscopes with digital outputs. This standard is directed toward, but not restricted to, general-purpose ... -
IEEE 14102
Abstract: This International Standard gives guidelines for the evaluation and selection of CASE tools, covering a partial or full portion of the software engineering life cycle. It establishes processes and activities to be applied ...Subject(s) : CASE tools , computer-aided software engineering (CASE) , information technology , life cycle processes , tool evaluation , tool selection , -
IEEE 643
Abstract: The purpose of this guide is to provide application information to users of carrier equipment as applied on power transmission lines. Since the major applications of the power-line carrier (PLC) is for protective relaying, ...Subject(s) : carrier equipment , insulated shield-wire systems , intrabundle conductor systems , power transmission lines , power-line carrier , -
IEEE 1730
Abstract: Overview
This recommended practice defines the processes and procedures that should be followed by users of distributed simulations to develop and execute their simulations; it is intended as a ...Subject(s) : DIS , distributed simulation , engineering methodology , HLA , IEEE 1730 , M&S , system process , TENA , -
IEEE 1277
Abstract: The scope of this standard is the definition and specification of the requirements and test code for dry-type and oil-immersed smoothing reactors for high-voltage direct current (HVDC) power transmission. This standard ...Subject(s) : construction , dry-type air-core , HVDC , oil-immersed , rating , smoothing reactors , test code application , -
IEEE C57.124
Abstract: This recommended practice applies to the detection of partial discharges occurring in the insulation of dry-type transformers or their components, and to the measurement of the associated apparent charge at the terminals ...Subject(s) : Apparent charge , corona , cost coil transformers , dry-type transformers , partial discharge , ventilated dry-type transformers , -
IEEE 1289
Abstract: Foreword
System design considerations, information display and control techniques for use with computer-based displays, and human factors engineering guidance for the use of these techniques in nuclear power ...Subject(s) : displays , human factors engineering , nuclear power generating stations , -
IEEE 187
Abstract: Spurious radiation from sound and television broadcast receivers of the superheterodyne type are possible sources of interference with other radio services.
This standard describes the potential sources of spurious ... -
IEEE C63.4
Abstract: This standard specifies U.S. consensus standard methods, instrumentation, and facilities for measurement of radio-frequency (RF) signals and noise emitted from electrical and electronic devices in the frequency range 9 kHz ...Subject(s) : conducted emission testing , conducting ground plane , digital equipment , electric-field measurement , intentional radiators , line impedance stabilization network , low-voltage electrical equipment , low-voltage electronic equipment , magnetic field measurement , normalized site attenuation , radiated emission testing , radio-noise emissions , radio-noise power , site attenuation , unintentional radiators , -
IEEE 43
Abstract: This document describes a recommended procedure for measuring insulation resistance of armature and field windings in rotating machines rated 1 hp, 750 W or greater. It applies to synchronous machines, induction machines, ...Subject(s) : absorption current , conduction current , discharge current , geometric capacitive current , insulation resistance , polarization index , surface leakage current , -
IEEE N42.18
Abstract: Foreword
The Joint Subcommittee of American National Standards Committees N13 and N42, which was responsible for the development of this standard, was established by authority of the Chairmen of American National Standards ... -
IEEE C57.12.90
Abstract: This standard describes methods for performing tests specified in IEEE Std C57.12.00™ and other standards applicable to liquid-immersed distribution, power, and regulating transformers.1 It is intended for use as a ...Subject(s) : transformer tests , -
IEEE 1561
Abstract: This guide provides rationale and guidance for operating lead-acid batteries in remote hybrid power systems, taking into consideration system loads and the capacities of the system's renewable-energy generator(s), dispatchable ... -
IEEE 11073-30300
Abstract: Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ... -
IEEE 1476
Abstract: This standard prescribes the electrical interfaces among the components comprising the auxiliary power systems and their electrical interface with other train-borne systems. As such, this standard treats the auxiliary power ... -
IEEE C57.12.00
Abstract: This standard describes electrical and mechanical requirements of liquid-immersed distribution and power transformers, and autotransformers and regulating transformers, single-phase and polyphase, with voltages of 601 V ...Subject(s) : autotransformers , distribution transformers , electrical requirements , mechanical requirements , power transformers , regulating transformers , -
IEEE 111
Abstract: General
This standard pertains to electronics wide-band transformers transmitting power within a wide band of frequencies covering typically at least one decade in the frequency spectrum. It is not ...Subject(s) : Balance test , balun , communication transformer , data transformer , harmonic distortion , impedance , insertion loss , matching transformers , return loss , transformer , video transformer , wideband , -
IEEE 11073-20601
Abstract: Within the context of the ISO/IEEE 11073 family of standards for device communication, this standard defines a common framework for making an abstract model of personal health data available in transport-independent transfer ... -
IEEE C135.3
Abstract: This standard covers zinc-coated steel lag screws of the fetter drive, gimlet point, and twist drive types commonly used in overhead line construction.