درباره ما
ISA - International Society of Automation
Browse by
Recent Submissions
-
ISA 95.00.07
Abstract: This standard defines technology independent services and messages for associating and mapping aliases (equivalent identifiers) and associated context that are exchanged between manufacturing operations domain applications ... -
ISA 96.08.01
Abstract: This standard provides basic requirements for mechanical integrity, selection and sizing of gas over oil actuators, both rotary and linear, provided in double and single acting designs. Actuators for rotary applications ... -
ISA 62443-4-1
Abstract: This part of ISA-62443 specifies process requirements for the secure development of products used in industrial automation and control systems. It defines a secure development life-cycle (SDL) for the purpose of developing ... -
ISA 61511-2
Abstract: This part of IEC 61511 provides guidance on the specification, design, installation, operation and maintenance of SIFs and related SIS as defined in IEC 61511-1:2016. NOTE 1 Annex A (informative) has been organized so that ... -
ISA TR100.20.01
Abstract: The Concepts and Terminology Technical Report (C&TTR) for Common Network Management (CNM) provides an overview, principles, concepts of CNM, terminology related to, and the expected benefits from, adopting a CNM standard. ... -
ISA 61511-1
Abstract: This part of IEC 61511 gives requirements for the specification, design, installation, operation and maintenance of a safety instrumented system (SIS), so that it can be confidently entrusted to achieve or maintain a safe ... -
ISA 61511-3
Abstract: This part of IEC 61511 provides information on: – the underlying concepts of risk and the relationship of risk to safety integrity (see Clause A.4); – the determination of tolerable risk (see Annex K); – ... -
ISA TR96.05.01
Abstract: ISA-TR96.05.01-2017: • is informative and does not contain any mandatory requirements. • is limited to automated valves normally operating in either a full open or full closed position. • introduces the ... -
ISA TR18.2.1
Abstract: This technical report was written in support of the standard ANSI/ISA-18.2-2016, Management of Alarm Systems for the Process Industries (March 2016), hereinafter referred to as ISA-18.2. The goal of this technical report ... -
ISA TR18.2.7
Abstract: General considerations This technical report provides guidance on how to integrate packaged systems (PSs) into a BPCS-based centralized alarm system. The scope includes discussing various issues that can arise when ISA-18.2 ... -
ISA TR84.00.09
Abstract: This document is intended to address and provide guidance on integrating the cybersecurity lifecycle with the safety lifecycle as they relate to Safety Controls, Alarms, and Interlocks (SCAI), inclusive of Safety Instrumented ... -
-
ISA TR106.00.02
Abstract: This technical report provides information regarding the work processes involved in the lifecycle of automated procedures for continuous process operations. The work processes that are unique to automating procedures are ... -
ISA TR84.00.08
Abstract: This technical report (TR) addresses wireless technology-based sensors that are used in Independent Protection Layers (IPLs) providing a risk reduction factor of less than or equal to 10 (non-SIS IPL) by the authority ... -
ISA RP105.00.01
Abstract: General applicability The recommended practice detailed in this document defines a baseline definition and model of a quality management system that can be utilized to implement and maintain a calibration program for ... -
ISA 62443-4-2
Abstract: This document in the ISA‑62443 series provides detailed technical control system component requirements (CRs) associated with the seven foundational requirements (FRs) described in ISA‑62443‑1‑1 [1] ... -
ISA 75.08.09
Abstract: Scope: This standard applies to sliding stem flangeless control valves, sizes 20 mm (3/4 inch) through 600 mm (24 inches) for Classes 150, 300, and 600. The face-to-face dimensions listed apply only to control valves that ... -
ISA 75.08.05
Abstract: Scope: This standard applies to buttweld-end globe-style control valves, sizes 15 mm (1/2 inch) through 450 mm (18 inches) for Classes 150 through 2500, having top, top and bottom, port, or cage guiding. Purpose ... -
ISA 96.08.01
Abstract: Scope: This standard provides basic requirements for mechanical integrity, selection and sizing of gas over oil actuators, both rotary and linear, provided in double and single acting designs. Actuators for rotary applications ... -
ISA TR100.20.01
Abstract: Scope: The Concepts and Terminology Technical Report (C&TTR) for Common Network Management (CNM) provides an overview, principles, concepts of CNM, terminology related to, and the expected benefits from, adopting a CNM ...