درباره ما
ASTM - ASTM International: Recent submissions
Now showing items 1621-1640 of 39933
-
Standard Test Method for Gross Defects and Mechanical Damage in Metallic Coatings by Polysulfide Immersion
Abstract: 5.1 The purpose of the alkaline polysulfide immersion test is to determine the presence of mechanical damage, wear-through, and other gross defects in the coating. Most metallic coatings are intended to be protective and ... -
Standard Specification for Titanium and Titanium Alloy Seamless Pipe
Abstract: This specification covers the requirements for 34 grades of titanium and titanium alloy seamless pipe intended for general corrosion resisting and elevated temperature service. Alloys may be supplied in the following ... -
Standard Terminology for Copper and Copper Alloys
Abstract: 3.1 This terminology is not intended to apply to any standard, test method, practice, or other document not within the jurisdiction of Committee B05 on Copper and Copper Alloys. -
Standard Specification for General Requirements for Nickel and Nickel Alloys Seamless Pipe and Tube
Abstract: This general specification contains the mandatory requirements to the ASTM standards listed herein for seamless pipes and tubes made from nickel and nickel alloys. In case of conflict, the requirements listed in the ... -
Standard Specification for Water Flushable Liquid and Paste Fluxes for Soldering of Copper and Copper Alloy Tube
Abstract: This guide establishes the requirements and test methods for liquid and paste fluxes for joining by soldering of copper and copper alloy tube and fittings in plumbing, heating, air conditioning, mechanical, fire sprinkler, ... -
Standard Specification for Cobalt-Chromium-Nickel-Molybdenum-Tungsten Alloy
Bar or Rod Abstract: This specification covers cobalt-chromium-nickel-molybdenum-tungsten alloy (UNS R31233) in the form of a rod for wear applications and general corrosion service. The requirements for the chemical composition hardness and ... -
Standard Specification for Precipitation Hardening Nickel Alloys Bar and Wire
Abstract: This specification covers UNS N07716, N07725, N07773, N07776, N09777, and N09925 nickel alloy hot or cold finished rounds, squares, hexagons, rectangles, and cold finished wires. Bars should be supplied in solution treated ... -
Standard Test Method for Surface Finger-Oxide Penetration Depth and Presence of Interparticle Oxide Networks in Powder Forged (PF) Steel Parts
Abstract: 5.1 The presence of surface finger-oxide penetration and interparticle oxide networks are two of the properties used to evaluate powder forged steel parts for proper processing. Maximum acceptable depths of penetration of ... -
Standard Test Method for Acid Resistance of Ceramic Decorations on Returnable Beer and Beverage Glass Containers
Abstract: 4.1 This test method evaluates the quality and serviceability of ceramic decorations on returnable beer and beverage containers. 4.2 This test method is also suitable for specification acceptance. Its significance is that ... -
Standard Test Method for Nonmetallic Inclusion Content of Ferrous Powders Intended for Powder Forging (PF) Applications
Abstract: 4.1 The extensive porosity present in pressed and sintered ferrous materials masks the effect of inclusions on mechanical properties. In contrast, the properties of material powder forged to near full density are strongly ... -
Standard Test Method for Determining the Percentage of Alloyed or Unalloyed Iron Contamination Present in Powder Forged (PF) Steel Materials
Abstract: 5.1 Cross-product contamination occurs whenever alloy steel powders are processed in the same equipment as iron powders. 5.2 Unalloyed iron particles, because they may not harden upon heat treatment, are a potential source ... -
Standard Specification for Materials for Ferrous Powder Metallurgy (PM) Structural Parts
Abstract: This specification covers a variety of ferrous powder metallurgy structural materials and includes a classification system or material designation code. The classification system includes chemical composition, minimum ... -
Standard Specification for Nickel-Chromium-Molybdenum-Niobium Alloy, Nickel-Chromium-Molybdenum-Silicon Alloy, and Nickel-Iron-Chromium-Molybdenum-Copper Alloy Welded Pipe
Abstract: This specification covers UNS N06625, N06219, and N08825 nickel-alloy welded pipe in the annealed condition. The pipe shall be manufactured from flat-rolled alloy by an automatic welding process with no additional filler ... -
Standard Specification for Seamless Copper Alloy (UNS No. C69100) Pipe and Tube
Abstract: This specification establishes the requirements for standard sized seamless pipes, both regular and extra strong, and seamless tubes in straight lengths produced from copper alloy UNS No. C69100 for general engineering ... -
Standard Test Method for Seal Quality of Anodic Coatings on Aluminum by Acid Dissolution
Abstract: 3.1 This test method describes a destructive test procedure for measuring the degree of seal of the porosity in anodic oxide coatings. Low coating mass loss is an indication of good seal quality and of the ability of the ... -
Standard Guide for Metallographic Sample Preparation of Cemented Tungsten Carbides
Abstract: 3.1 This sample preparation procedure may be used to prepare metallographic samples for Guide B657. It does not include all variations of sample preparation. -
Standard Test Method for Measuring Dimensional Changes Associated with Processing Metal Powders Intended for Die Compaction
Abstract: 5.1 Dimensional Change When Compacting and Sintering Metal Powders: 5.1.1 The dimensional change value obtained under specified conditions of compacting and sintering is a material characteristic inherent in the powder. ... -
Standard Specification for Aluminum-Alloy Rolled Tread Plate
Abstract: This specification covers aluminum-alloy rolled tread plate. Unless otherwise specified, all tread plate shall be supplied in the mill finish and shall be uniform as defined by the requirements and shall be commercially ... -
Standard Specification for Copper Alloy Addition Agents
Abstract: 11.1 For purposes of determining compliance with the specified limits for chemical composition, an observed or calculated value shall be rounded as indicated in accordance with the Rounding method of Practice E29. ... -
Standard Test Method for Alternating Current Magnetic Properties of Laminated Core Specimen Using Voltmeter-Ammeter-Wattmeter Methods
Abstract: 5.1 This test method was developed for evaluating the ac magnetic properties of laminated cores made from flat-rolled magnetic materials. 5.2 The reproducibility and repeatability of this test method are such that this ...