درباره ما
ASTM - ASTM International: Recent submissions
Now showing items 1681-1700 of 39933
-
Standard Specification for Forged Rings and Hollows for Use as Base Plates in Power Transmission Structures
Abstract: This specification is intended for high-strength, low-alloy forged rings and hollows produced from steels with atmospheric corrosion resistance for use as base plates in welded tubular structures. These steels have ... -
Standard Practice for Hot Isostatic Pressing of Steel, Stainless Steel, and Related Alloy Castings
Abstract: This practice covers general requirements for Hot Isostatic Pressing (HIP) of steel, stainless steel, and related alloy castings. HIP is a solid state process which applies heat and pressure simultaneously to objects in ... -
Standard Test Method for Crazing Resistance of Fired Glazed Ceramic Whitewares by a Thermal Shock Method
Abstract: 3.1 Unless there is a proper match between the expansions of the glaze and the body, all glazed whitewares may contain residual stresses from the firing that bonded the glaze to the body. In addition, whitewares are ... -
Standard Specification for Carbon-Steel Wire and Welded Wire Reinforcement, Plain and Deformed, for Concrete
Abstract: This specification covers the material, dimensional and mechanical property requirements for plain and deformed steel wire and welded wire reinforcements produced from hot-rolled rods that are to be used for the reinforcement ... -
Standard Specification for Deformed and Plain, Low-Carbon, Chromium, Steel Bars for Concrete Reinforcement
Abstract: This specification covers low-carbon, chromium, steel bars, deformed and plane for concrete reinforcement in cut lengths and coils. The bars shall be rolled from properly identified heats of mold cast or strand cast steel ... -
Standard Specification for Steel Sheet, Zinc-Aluminum-Magnesium Alloy-Coated by the Hot-Dip Process
Abstract: This specification covers steel sheet in coils and cut lengths coated with zinc-aluminum-magnesium alloy by hot-dip process intended for applications requiring corrosion resistance and paintability. The steel sheet shall ... -
Standard Specification for Higher-Strength Martensitic Stainless Steel Plate, Sheet, and Strip
Abstract: This specification covers the standard for martensitic stainless steel for various structural, architectural, pressure vessel, and heat-resisting applications. The material shall undergo heat-treatment by tempering. The ... -
Standard Specification for Mechanical Splices for Steel Reinforcing Bars
Abstract: 5.1 Significance: 5.1.1 The bar-splice assembly test specimen shall closely represent the mechanical splice used in practice. The behavior of the bar-splice assembly embedded in concrete, however, may differ from its ... -
Standard Specification for Steel, Sheet, Cold-Rolled, Carbon, Structural, High-Strength Low-Alloy, High-Strength Low-Alloy with Improved Formability, Required Hardness, Solution Hardened, and Bake Hardenable
Abstract: This specification covers cold-rolled, carbon steel sheets, in coils and cut lengths, in the following designations: commercial steels (CS Types A, B, and C); drawing steel (DS Types A and B); deep drawing steel (DDS); ... -
Standard Specification for Rail-Steel and Axle-Steel Deformed Bars for Concrete Reinforcement
Abstract: This specification covers rail-steel and axle-steel deformed bars for concrete reinforcement. The standard sizes and dimensions of deformed bars and their number designation are presented. The carbon determination, deformation ... -
Standard Guide for Editorial Procedures and Form of Product Specifications for Steel, Stainless Steel, and Related Alloys
Abstract: 4.1 The Form and Style Manual provides mandatory requirements and recommended practices for the preparation and content of ASTM specifications. In order to promote consistency in the style and content of product specifications ... -
Standard Specification for Lock-Strip Gaskets
Abstract: This specification defines the required properties of lock-strip gaskets where resistance to sunlight, weathering, flame, oxidation, permanent deformation under load, and diminution of gripping pressure are prime essentials. ... -
Standard Specification for Fusion-Bonded Epoxy-Coated Structural Steel H-Piles and Sheet Piling
Abstract: This specification covers the qualification requirements for structural steel H-piles and sheet piling with protective fusion-bonded epoxy coating applied by electrostatic spraying, flocking, or fluidized bed processing. ... -
Standard Specification for Steel Castings, Carbon and Alloy, with Tensile Requirements, Chemical Requirements Similar to Standard Wrought Grades
Abstract: This specification covers carbon and low-alloy steel castings. The steel specimens shall be heat treated and shall conform to the required values of austenitizing temperature and tempering temperature. The steel materials ... -
Standard Specification for Steel Sheet, Metallic-Coated by the Hot-Dip Process for Corrugated Steel Pipe
Abstract: This specification covers steel sheets used in the manufacture of corrugated steel pipe for storm sewers, culverts, drains, and similar uses. The sheet is metallic coated by the hot-dip process. Material for this use is ... -
Standard Specification for Uncoated, Weldless, 3-Wire Steel Strand for Prestressed Concrete
Abstract: This specification covers two types and two grades of 2- and 3-wire, uncoated weldless steel and strand for use in pretensioned and posttensioned prestressed concrete construction. One specimen for test shall be taken from ...