درباره ما
ASTM - ASTM International: Recent submissions
Now showing items 1661-1680 of 39933
-
Standard Test Method for Apparent Density of Metal Powders and Compounds Using the Scott Volumeter
Abstract: 4.1 This test method covers the evaluation of the apparent density physical characteristic of powders. The degree of correlation between the results of this test and the quality of powders in use will vary with each ... -
Standard Test Method for Modulus of Rupture of Unfired Clays
Abstract: 3.1 The purpose of this test method is to obtain values of rupture modulus of clays before firing, under various processing conditions (relative humidity). -
Standard Specification for Copper and Copper-Alloy Die Forgings (Hot-Pressed)
Abstract: This specification establishes the requirements for copper and copper die forgings produced by hot pressing method. The forgings included here are designated with the following Copper or Copper Alloy UNS Nos.: C11000 ... -
Standard Specification for Concentric-Lay-Stranded Aluminum Conductors, Coated-Steel Reinforced (ACSR)
Abstract: This specification covers concentric-lay-stranded aluminum conductors, coated-steel reinforced (ACSR), made from round aluminum 1350-H19 wires and round, coated steel core wire for use as overhead electrical conductors. ... -
Standard Specification for Copper-Beryllium Alloy Rod and Bar
Abstract: This specification establishes the requirements for rods and bars in straight lengths of copper-beryllium alloys with Copper Alloy UNS Nos. C17000, C17200, and C17300. The material for manufacture shall be cast and worked ... -
Standard Specification for Copper-Alloy Plate and Sheet for Pressure Vessels, Condensers, and Heat Exchangers
Abstract: This specification establishes the requirements for plates, sheets, and circles cut from plates and sheets made of UNS C36500, C44300, C44400, C44500, C46400, C46500, C61300, C61400, C63000, C63200, C70600, C70620, C71500, ... -
Standard Specification for Nickel-Chromium-Aluminum Alloy, Nickel-Chromium-Iron Alloys, Nickel-Chromium-Cobalt-Molybdenum Alloy, Nickel-Iron-Chromium-Tungsten Alloy, and Nickel-Chromium-Molybdenum-Copper Alloy Rod, Bar, and Wire
Abstract: This specification covers nickel-chromium-iron alloys (UNS N06600, N06601, N06603, N06690, N06693, N06025, N06045, and N06696) and nickel-chromium-cobaltmolybdenum alloy (UNS N06617) in the form of hot-finished and cold-worked ... -
Standard Specification for Oxygen-Free Electrolytic Copper—Refinery Shapes
Abstract: This specification covers grade 1 ( UNS C10100) and grade 2 (UNS C10200) of oxygen-free electrolytic copper wire bars, billets, and cakes produced without the use of metallic or metaloidal deoxidizers. The chemical composition ... -
Standard Specification for Copper Sheet, Strip, Plate, and Rolled Bar
Abstract: This standard covers the requirements for copper sheet, strip, plate, and rolled bar produced from copper with the following UNS Nos.; C10100, C10200, C10300, C10400, C10500, C10700, C10800, C10910, C11000, C11300, C11400, ... -
Standard Specification for Nickel Rod and Bar
Abstract: This specification covers nickel (UNS N02200), low carbon nickel (UNS N02201), and solution strengthened nickel (UNS N02211) in the form of hot-worked, cold-worked, or annealed rods and bars of round, square, hexagonal, ... -
Standard Specification for Commercial Bronze Strip for Bullet Jackets
Abstract: 17.1 For purposes of determining compliance with the specified property limits for the properties listed in the following table, an observed value of a calculated value shall be rounded as indicated in accordance with the ... -
Standard Practice for Coking Large Shapes of Carbon-Bearing Materials
Abstract: 3.1 This practice is useful for preparing coked specimens for subsequent testing where the shapes desired cannot be fitted into the coking box described in Test Methods C831. 3.2 This practice can be very sensitive to ... -
Standard Specification for Aluminum-Bronze Sand Castings
Abstract: This specification establishes requirements for sand castings produced from copper-base alloys having the alloy numbers, commercial designations, and nominal compositions. The alloys the classified according to their nominal ... -
Standard Specification for Copper and Copper-Alloy Seamless Condenser Tubes and Ferrule Stock
Abstract: This specification establishes the requirements for seamless tube and ferrule stock of copper and various copper alloys of a specified range of diameters, for use in surface condensers, evaporators, and heat exchangers. ... -
Standard Specification for Electrolytic Copper Cathode
Abstract: 13.1 Calculated values shall be rounded to the desired number of places as directed in Practice E29. -
Standard Specification for Free-Cutting Brass Rod, Bar and Shapes for Use in Screw Machines
Abstract: This specification establishes the requirements for free-cutting brass rod, bar, wire, and shapes of any specified cross-section produced from Copper Alloy UNS No. C36000 suitable for high-speed screw machining applications ... -
Standard Practice for Construction of Mechanically Stabilized Earth Walls with Inextensible Soil Reinforcement
Abstract: 4.1 Mechanically stabilized earth walls (MSEW) are engineered earth retaining structures comprised of pre-fabricated wall facing elements and engineered backfill that is reinforced with inextensible steel elements. The ...