درباره ما
ASTM - ASTM International: Recent submissions
Now showing items 1821-1840 of 39933
-
Standard Specification for Steel Springs, Helical, Heat-Treated
Abstract: This specification covers the standard for hot-coiled, heat-treated helical compression springs with tapered, closed, squared and ground ends made of hot-wrought round steel bars. Cross sections for hot-wrought round, ... -
Standard Specification for Steel Castings, High Strength, for Structural Purposes
Abstract: This specification covers the standard for carbon steel, alloy steel, and martensitic stainless steel castings that are to be subjected to higher mechanical stresses. All castings shall undergo heat treatment either by ... -
Standard Specification for Steel, Strip, Carbon (0.25 Maximum Percent), Cold-Rolled
Abstract: This specification covers cold-rolled carbon steel strip in cut lengths or coils, furnished to closer tolerances than cold-rolled carbon steel sheet. The steel shall be made by the open-hearth, basic-oxygen, or electric-furnace ... -
Standard Specification for Steel Bar, Carbon and Alloy, Cold-Finished
Abstract: This specification covers cold-finished carbon and alloy steel bars for heat treatment, machining into components, or for as-finished condition as shafting or in constructional applications. The steel materials shall be ... -
Standard Specification for Pipe, Steel, Black and Hot-Dipped, Zinc-Coated, Welded and Seamless
Abstract: This specification covers seamless and welded black and hot-dipped galvanized steel pipe in NPS 1/8 to NPS 26. The steel categorized in this standard must be open-hearth, basic-oxygen or electric-furnace processed and must ... -
Standard Specification for Carbon Steel Forgings for Piping Applications
Abstract: This specification covers standards for forged carbon steel piping components, that is, flanges, fittings, valves, and similar parts, for use in pressure systems at ambient and higher-temperature service conditions. Materials ... -
Standard Specification for General Requirements for Rolled Structural Steel Bars, Plates, Shapes, and Sheet Piling
Abstract: This specification deals with the general requirements that apply to rolled structural steel bars, plates, shapes, and sheet piling. The steel shall be made in an open-hearth, basic-oxygen, or electric-arc furnace followed ... -
Standard Practice for Evaluating and Qualifying Oilfield and Refinery Corrosion Inhibitors Using Jet Impingement Apparatus
Abstract: 5.1 Selection of corrosion inhibitor for oilfield and refinery applications involves qualification of corrosion inhibitors in the laboratory (see Guide G170). Field conditions should be simulated in the laboratory in a ... -
Standard Specification for Mineral Fiber Thermal Insulating Cement
Abstract: This specification covers mineral fiber thermal insulating materials in the form of dry cement, which, when mixed with a suitable proportion of water, applied as a plastic mass, and dried in place, affords resistance to ... -
Standard Practice for Evaluating and Qualifying Oil Field and Refinery Corrosion Inhibitors Using the Rotating Cylinder Electrode
Abstract: 5.1 Selection of corrosion inhibitor for oil field and refinery applications involves qualification of corrosion inhibitors in the laboratory (see Guide G170). Field conditions should be simulated in the laboratory in a ... -
Standard Practice for Evaluating and Qualifying Oil Field and Refinery Corrosion Inhibitors Using Rotating Cage
Abstract: 5.1 Selection of corrosion inhibitor for oil field and refinery applications involves qualification of corrosion inhibitors in the laboratory (see Guide G170). Field conditions should be simulated in the laboratory in a ... -
Standard Guide for Statistical Analysis of Accelerated Service Life Data
Abstract: 4.1 The nature of accelerated service life estimation normally requires that stresses higher than those experienced during service conditions are applied to the material being evaluated. For non-constant use stress, such ... -
Standard Test Method for Ranking Resistance of Plastics to Sliding Wear Using Block-on-Ring Wear Test—Cumulative Wear Method
Abstract: 5.1 The significance of this test method in any overall measurement program directed toward a service application will depend on the relative match of test conditions to the conditions of the service application. 5.2 This ... -
Standard Test Method for Evaluating Pipeline Coating Patch Materials
Abstract: 3.1 Holidays in pipeline coatings may be repaired by circumferential wrapping with a suitable pipe wrap tape. However, this technique is not always practicable and patching may be required. The effectiveness of a patch ... -
Standard Guide for Conducting and Evaluating Galvanic Corrosion Tests in Electrolytes
Abstract: 3.1 Use of this guide is intended to provide information on the galvanic corrosion of metals in electrical contact in an electrolyte that does not have a flow velocity sufficient to cause erosion-corrosion or cavitation. ... -
Standard Test Method for Drying and Firing Linear Change of Refractory Plastic and Ramming Mix Specimens
Abstract: 3.1 This test method is useful in quantitatively rating or ranking both ramming and refractory plastics by their linear stability after heating. 3.2 This test method is also useful for determining whether a ramming or ... -
Standard Test Method for Chemical Resistance of Pipeline Coatings
Abstract: 4.1 The data obtained for short-term tests are of interest only in eliminating the most unsuitable materials or for indicating a probable order of resistance in any particular media. 4.2 Test conditions should take into ... -
Standard Test Method for Penetration Resistance of Pipeline Coatings (Blunt Rod)
Abstract: 3.1 Since pipeline coatings are subjected to concentrated pressures exerted by the weight of the pipe and the backfill, this test is intended primarily for determining the resistance of the coating to penetration or ... -
Standard Test Method for Specific Bendability of Pipeline Coatings
Abstract: 4.1 This test will provide information on the ability of coatings applied to pipe to resist cracking, disbonding, or other mechanical damage as a result of bending. Because the test is applied to coated pipe from commercial ... -
Standard Test Method for Impact Resistance of Pipeline Coatings (Falling Weight Test)
Abstract: 4.1 The ability of a pipe coating to resist mechanical damage during shipping, handling, and installation will depend upon its impact resistance. This test method provides a systematic means for screening coating materials ...