درباره ما
ASTM - ASTM International: Recent submissions
Now showing items 3061-3080 of 39933
-
Standard Test Method for Bursting Strength of Fabrics Constant-Rate-of-Extension (CRE) Ball Burst Test
Abstract: 5.1 This method is used to determine the force required to rupture textile fabric by forcing a steel ball through the fabric with a constant-rate-of-extension tensile tester. 5.2 This is a new method and therefore the ... -
Standard Specification for Repositionable Pressure-Sensitive Flags
Abstract: This specification covers repositionable pressure-sensitive flags used to mark, flag, and index documents, books, periodicals, and so forth. Flags covered here consist of a single sheet of matte film partially covered by ... -
Standard Guide for Quality Control and Quality Assurance Procedures for Aromatic Hydrocarbons and Related Materials
Abstract: 5.1 Quality Control and Quality Assurance practices are important for the optimum operation of testing laboratories using D16 methods for aromatic hydrocarbons and related materials. Quality procedure guidelines, like those ... -
Standard Specification for Repositionable Note Pad
Abstract: This specification covers pads of repositionable, colored, note paper. Each sheet has a strip of pressure-sensitive adhesive on the back side. A hand-operated steel roller shall be used in the manufacture of the pads and ... -
Standard Test Method for Elemental, Oxidized, Particle-Bound and Total Mercury in Flue Gas Generated from Coal-Fired Stationary Sources (Ontario Hydro Method)
Abstract: 5.1 The measurement of particle-bound, oxidized, elemental, and total mercury in stationary-source flue gases provides data that can be used for emissions assessments and reporting, the certification of continuous mercury ... -
Standard Test Method for Abrasion Resistance of Textile Webbing (Hex Bar Method)
Abstract: 5.1 The measurement of the resistance to abrasion of textile webbing is very complex. The resistance to abrasion is affected by many factors that include the inherent mechanical properties of the fibers; the dimensions of ... -
Standard Specification for Biodiesel Fuel Blendstock (B100) for Middle Distillate Fuels
Abstract: This specification covers biodiesel fuel blend stock, B100, in Grades S15 and S500 for use as a blend component with middle distillate fuels. This specification prescribes the required properties of diesel fuels at the ... -
Standard Practice for Sampling Liquids Using Grab and Discrete Depth Samplers
Abstract: 4.1 Sampling at specified depth(s) within a liquid may be needed to confirm or rule out variations within a target population. This practice describes the design and operation of commercially available grab and discrete ... -
Standard Test Method for Determination of Individual Components in Spark Ignition Engine Fuels by 50-Metre Capillary High Resolution Gas Chromatography
Abstract: 5.1 Knowledge of the individual component composition (speciation) of gasoline fuels and blending stocks is useful for refinery quality control and product specification. Process control and product specification compliance ... -
Standard Test Method for Linear Thermal Expansion of Electrode Carbons
Abstract: 5.1 Coefficients of linear thermal expansion are used for design and quality control purposes and to determine dimensional changes of parts and components (such as carbon anodes, cathodes, and so forth) when subjected to ... -
Standard Test Method for Determination of Chlorine in Coal by Oxidative Hydrolysis Microcoulometry
Abstract: 4.1 This test method permits measurements of the total chlorine mass fraction in coal. -
Standard Test Method for Total Ash in Wet Blue or Wet White
Abstract: 4.1 This test method is useful in determining the approximate amount of nonvolatile inorganic material in wet blue. This may be in the form of salts or oxides of the elements. In a mixed-chrome tannage, the approximate ... -
Standard Practice for Statistical Assessment and Improvement of Expected Agreement Between Two Test Methods that Purport to Measure the Same Property of a Material
Abstract: 5.1 This practice can be used to determine if a constant, proportional, or linear bias correction can improve the degree of agreement between two methods that purport to measure the same property of a material. 5.2 The ... -
Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence VIII Spark-Ignition Engine (CLR Oil Test Engine)
Abstract: 5.1 This test method is used to evaluate automotive engine oils for protection of engines against bearing weight loss. 5.2 This test method is also used to evaluate the SIG capabilities of multiviscosity-graded oils. ... -
Standard Specification for Extruded and Compression Molded Shapes Made from Poly(Vinylidene Fluoride) (PVDF)
Abstract: This specification covers the requirements and test methods for the material, dimensions, and workmanship, and the properties of extruded sheet, rod and tubular bar manufactured from Poly(Vinylidene Fluoride) (PVDF). The ... -
Standard Practice for Sampling Liquids Using Bailers
Abstract: 5.1 A bailer is a device for obtaining a sample from stratified or un-stratified waters and liquid wastes. The most common use of a bailer is for sampling ground water from single-screened wells (Fig. 1) and well clusters ... -
Standard Test Method for Determining Water Vapor Transmission Rates Through Nonwoven and Plastic Barriers
Abstract: 5.1 The purpose of this test method is to obtain values for the WVTR of barrier materials. 5.2 WVTR is an important property of materials and can be related to shelf life; product stability, breath-ability, and wearing ... -
Standard Test Method for Determining Aerobic Biodegradation of Plastic Materials in the Marine Environment by a Defined Microbial Consortium or Natural Sea Water Inoculum
Abstract: 5.1 The use of plastics aboard ships is on the rise and the use of the sea as a trash dumping site is no longer a possibility; consequently, the disposal of plastic materials while at sea remains a major issue. It is ... -
Standard Practice for Evaluation of Aging Resistance of Pre-stressed Prepainted Metal in a Boiling Water Test
Abstract: 3.1 Prepainted metal is supplied as a painted coil, and it is fabricated into a finished part. The fabrication process induces stress to the paint system. To determine if this stress will lead to a failure in service, it ...