درباره ما
ASME - ASME International: Recent submissions
Now showing items 781-800 of 1083
-
ASME PTB-4
Abstract: Example problems illustrating the use of the design-by-rule methods in ASME B&PV Code, Section VIII, Division 1 are provided in this document. Example problems are provided for most of the calculation procedures in either ... -
ASME B94.49
Abstract: This standard covers nomenclature, definitions, sizes and tolerances for spade drill blades and spade drill holders insofar as the holder locates and holds the spade drill blade. All dimensions are in inches. Conversion ... -
ASME B18.2.3.9M
Abstract: (a) This Standard covers the complete dimensional and general data for metric series heavy hex flange screws recognized as American National Standard.
(b) The inclusion of dimensional data in this ... -
ASME B107.17
Abstract: This Standard establishes final inspection gage sizes and test mandrel sizes for wrench openings and spark plug wrench openings for inch and metric sizes. This Standard does not cover every available size, but only those ... -
ASME B89.7.4.1
Abstract: This Technical Report provides guidelines for setting gauging (or test) limits in support of accept/reject decisions in workpiece inspections, instrument verifications, and general conformance tests where uncertain numerical ... -
ASME Y14.37
Abstract: This Standard establishes the definition of composite parts that are not covered within the existing ASME Y14 Series of standards. This Standard defines exceptions and additional requirements to existing ASME standards for ... -
ASME A112.18.2
Abstract: Scope:This Standard covers plumbing waste fittings of sizes NPS-2 and smaller.
This ...
-
ASME PTC 29
Abstract: This Code applies to speed governors used on conventional, constant-speed hydraulic turbines. This Code is applicable to electronic-hydraulic and mechanical-hydraulic speed governors. These governors are commonly used to ... -
ASME B30.14
Abstract: SCOPE EXCLUSIONS
Any exclusion of, or limitations applicable to the equipment, requirements, recommendations, or operations contained in this Standard are established in the affected volume’s ... -
ASME EA-2G
Abstract: This guidance document provides an application guide on how to utilize ASME EA-2, Energy Assessment for Pumping Systems. This guidance document provides background and supporting information to assist in applying the ... -
ASME B5.35
Abstract: This Standard covers ANSI Standard practice for location and size of bolt holes for mounting abrasive discs and plate mounted wheels.
PURPOSE
To provide standards to be used in the design of machine ... -
ASME B18.25.2M
Abstract: This Standard covers requirements for metric Woodruff keys and keyways intended for both alignment of shafts and hubs, and transmitting torque between shafts and hubs.
The inclusion of dimensional data in this ...Subject(s) : KEY , WOODRUFF , -
ASME B5.9
Abstract: Scope and Purpose
These spindle noses are for use on engine lathes, tool room lathes, turret lathes and automatic lathes and may be used advantageously on other machines wherever chucks or fixtures ... -
ASME B20.1 INTERPRETATIONS
Abstract: This Standard applies to the design, construction, installation, maintenance, inspection, and operation of conveyors and conveying systems in relation to hazards. The conveyors may be of the bulk material, package, or ... -
ASME B18.24
Abstract: This Standard is intended to provide all users (manufacturers, distributors, design and configuration, parts control. inventory control, test and maintenance functions) with the capability to identify externally threaded, ... -
ASME STP-PT-050
Abstract: INTRODUCTION
When heavy-wall pipe field welds are radiographed, common practice is to route the radiation source through a hole in a pipe near a weld, and locate it on the centerline using a J-shaped ... -
ASME B18.2.3.4M
Abstract: (a) This Standard covers the complete dimensional and general data for metric series hex flange screws recognized as American National Standard.
(b) The inclusion of dimensional data in this Standard is not ... -
ASME B89.7.1 TECH RPT
Abstract: This Technical Report provides recommendations associated with addressing measurement uncertainty and direction in the application of the existing ASME B89.7 series of uncertainty-related standards and technical reports. ... -
ASME Y14.41
Abstract: shes requirements and references documents applicable to the preparation and revision of digital product definition data, hereafter referred to as data sets. This Standard defines exceptions and additional requirements to ...