French -- Appareillage à basse tension – Partie 4-1: Contacteurs et démarreurs de moteurs – Contacteurs et démarreurs électromécaniques - Edition 4.0|English -- Low-voltage switchgear and controlgear – Part 4-1: Contactors and motor-starters – Electromechanical contactors and motor-starters - Edition 4.0
IEC 60947-4-1
Organization:
IEC - International Electrotechnical Commission
Year: 2018
Abstract: Scope: This part of IEC 60947 is applicable to the following equipment: – electromechanical contactors and starters including motor protective switching device (MPSD); – actuators of contactor relays; – contacts dedicated exclusively to the coil circuit of this contactor or this contactor relay; – dedicated accessories (e.g. dedicated wiring, dedicated latch accessory); intended to be connected to distribution circuits, motors circuits and other load circuits, the rated voltage of which does not exceed 1 000 V AC or 1 500 V DC. This document covers also the assessment procedure for electromechanical overload protection used in safety applications such as protecting a motor located in explosive atmosphere from the outside atmosphere: See Annex L. This document does not apply to: – starters for DC motors 1; NOTE 1 The requirements for DC motor starters are under consideration for the next maintenance cycle. – auxiliary contacts of contactors and contacts of contactor relays. These are covered by IEC 60947-5-1; – starter used downstream to frequency drive1; NOTE 2 Additional requirements for starter used downstream to frequency drive are under consideration for the next maintenance cycle. – short-circuit protective device integrated within starters other than MPSDs. This is covered by IEC 60947-2 and IEC 60947-3; – the use of the product with additional measure within explosive atmospheres. These are given in IEC 60079 series; – embedded software design rules1; – cyber security aspects. These are covered by IEC 62443 series. The objective of this document is to state: a) the characteristics of the equipment; b) the conditions applicable to the equipment with reference to: 1) its operation and behaviour, 2) its dielectric properties, 3) its degree of protection 4) its construction including safety measures against electric shock, fire hazard and mechanical hazard; c) the tests intended for confirming that these conditions have been met, and the methods to be adopted for these tests; d) the information to be given with the equipment or in the manufacturer\'s literature. 1 For this subject the manufacturer is responsible for taking additional safety measures.
Collections
:
-
Statistics
French -- Appareillage à basse tension – Partie 4-1: Contacteurs et démarreurs de moteurs – Contacteurs et démarreurs électromécaniques - Edition 4.0|English -- Low-voltage switchgear and controlgear – Part 4-1: Contactors and motor-starters – Electromechanical contactors and motor-starters - Edition 4.0
Show full item record
contributor author | IEC - International Electrotechnical Commission | |
date accessioned | 2020-09-15T22:28:51Z | |
date available | 2020-09-15T22:28:51Z | |
date copyright | 2018.10.01 | |
date issued | 2018 | |
identifier other | CZZKGGAAAAAAAAAA.pdf | |
identifier other | CZZKGGAAAAAAAAAA.pdf | |
identifier uri | https://yse.yabesh.ir/std/handle/yse/289125 | |
description abstract | Scope: This part of IEC 60947 is applicable to the following equipment: – electromechanical contactors and starters including motor protective switching device (MPSD); – actuators of contactor relays; – contacts dedicated exclusively to the coil circuit of this contactor or this contactor relay; – dedicated accessories (e.g. dedicated wiring, dedicated latch accessory); intended to be connected to distribution circuits, motors circuits and other load circuits, the rated voltage of which does not exceed 1 000 V AC or 1 500 V DC. This document covers also the assessment procedure for electromechanical overload protection used in safety applications such as protecting a motor located in explosive atmosphere from the outside atmosphere: See Annex L. This document does not apply to: – starters for DC motors 1; NOTE 1 The requirements for DC motor starters are under consideration for the next maintenance cycle. – auxiliary contacts of contactors and contacts of contactor relays. These are covered by IEC 60947-5-1; – starter used downstream to frequency drive1; NOTE 2 Additional requirements for starter used downstream to frequency drive are under consideration for the next maintenance cycle. – short-circuit protective device integrated within starters other than MPSDs. This is covered by IEC 60947-2 and IEC 60947-3; – the use of the product with additional measure within explosive atmospheres. These are given in IEC 60079 series; – embedded software design rules1; – cyber security aspects. These are covered by IEC 62443 series. The objective of this document is to state: a) the characteristics of the equipment; b) the conditions applicable to the equipment with reference to: 1) its operation and behaviour, 2) its dielectric properties, 3) its degree of protection 4) its construction including safety measures against electric shock, fire hazard and mechanical hazard; c) the tests intended for confirming that these conditions have been met, and the methods to be adopted for these tests; d) the information to be given with the equipment or in the manufacturer\'s literature. 1 For this subject the manufacturer is responsible for taking additional safety measures. | |
language | English, French | |
title | French -- Appareillage à basse tension – Partie 4-1: Contacteurs et démarreurs de moteurs – Contacteurs et démarreurs électromécaniques - Edition 4.0|English -- Low-voltage switchgear and controlgear – Part 4-1: Contactors and motor-starters – Electromechanical contactors and motor-starters - Edition 4.0 | en |
title | IEC 60947-4-1 | num |
type | standard | |
page | 376 | |
status | Active | |
tree | IEC - International Electrotechnical Commission:;2018 | |
contenttype | fulltext |