درباره ما
SAE - SAE International: Recent submissions
Now showing items 881-900 of 16264
-
Bearing and Bushing Alloys
Abstract: The bearing performance of steel backed half bearings, bushings, and washers is dependent on the properties and thickness of the lining alloy, the strength and dimensional stability of the steel backing (usually SAE 1010) ... -
Fifth Wheel Kingpin, Heavy Duty - Commercial Trailers and Semitrailers
Abstract: This SAE Recommended Practice applies to fifth wheel kingpins for heavy-duty commercial trailers and semitrailers, used for off-highway operation or in hauling heavy loads (see Figure 1). -
Cartridge Cavity
Abstract: This SAE Standard covers complete general and dimensional data for the manufacture of, T6061-T6 Aluminum cavities designed to receive Push To Connect threadless fittings known as “cartridges“, for air brake applications. ... -
Sintered Carbide Tools
Abstract: This recommended practice covers methods for measuring or evaluating five properties or characteristics of sintered carbide which contribute significantly to the performance of sintered carbide tools. These properties are: ... -
Alloy and Temper Designation Systems for Aluminum
Abstract: This standard provides systems for designating wrought aluminum and wrought aluminum alloys, aluminum and aluminum alloys in the form of castings and foundry ingot, and the tempers in which aluminum and aluminum alloy ... -
Safety Signs for Off-Road Work Machines
Abstract: SAE J115 specifies the relevant ISO standards for application to safety signs for use on off-road work machines as defined in SAE J1116. -
Automatic Transmission Functions—Terminology
Abstract: The following is a list of the most common terminology used in describing automatic transmission functions. -
Guide for Reliability Analysis Using the Physics-of-Failure Process
Abstract: The Physics-of-Failure (PoF) is a science-based approach to reliability that uses modeling and simulation to design-in reliability. This approach models the root causes of failures such as fatigue, fracture, wear, and ... -
Early Acquisition and Preservation of Information in a Motor Vehicle Crash
Abstract: The purpose of this SAE Recommended Practice is to offer simplified and prioritized guidelines for collecting and preserving on-scene data related to motor vehicle crashes. It is intended that these guidelines improve the ... -
Recommended Practices for Fluid Conductor Carbon, Alloy and High Strength Low Alloy Steel Tubing Applications - Part 3: Procurement
Abstract: SAE J2551-3 recommended practice provides recommendations for a procurement process for carbon, alloy and high strength low alloy steel tube assemblies for fluid power applications utilizing commonly available manufacturing ... -
Wiring Distribution Systems for Off-Road, Self-Propelled Work Machines
Abstract: This SAE Standard specifies requirements and design guidelines for electrical wiring systems of less than 50 V and cable diameters from 0.35 to 19 mm2 used on off-road, self-propelled earthmoving machines as defined in SAE ... -
Performance Requirements for Motor Vehicle Headlamps
Abstract: This SAE Recommended Practice is intended as a guide toward standard practice and is subject to change to keep pace with experience and technical advances. This document establishes performance requirements for headlamps. -
Surface Hardness Testing with Files
Abstract: Hardness testing with files consists essentially of cutting or abrading the surface of metal parts, and approximating the hardness by the feel, or extent to which, the file bites into the surface. The term file hard means ... -
Low Speed Enveloping Test with Perpendicular and Inclined Cleats
Abstract: This SAE Recommended Practice describes a test method for measuring the forces and moments generated at a spindle when a tire rolls over a rectangular obstacle, cleat, at very low speed. The cleat used in a particular test ... -
Immunity to Conducted Transients on Power Leads
Abstract: This SAE Standard defines methods and apparatus to evaluate electronic devices for immunity to potential interference from conducted transients along battery feed or switched ignition inputs. Test apparatus specifications ... -
Selection and Heat Treatment of Tool and Die Steels
Abstract: The information in this report covers data relating to SAE J438, Tool and Die Steels, and is intended as a guide to the selection of the steel best suited for the intended purpose and to provide recommended heat treatments ... -
Elevated Temperature Properties of Cast Irons
Abstract: The purpose of this SAE Information Report is to provide automotive engineers and designers with a concise statement of the basic characteristics of cast iron under elevated temperature conditions. As such, the report ... -
All-Wheel-Drive-Drivetrain Schematic Symbol Standards
Abstract: In this SAE Recommended Practice, attention will be given to passenger cars and light trucks (through Class III). -
Solders
Abstract: The choice of the type and grade of solder for any specific purpose will depend on the materials to be joined and the method of applying. Those with higher amounts of tin usually wet and bond more readily and have a narrower ... -
Special Purpose Alloys (Superalloys)
Abstract: The data given in Tables 1–4 are typical values only and are not intended for design parameters. Mechanical properties of the special purpose alloys depend greatly upon processing variables and heat treatment. It is ...