درباره ما
NAVY - AS - Naval Air Systems Command: Recent submissions
Now showing items 1341-1360 of 2147
-
MIL-HDBK-2084 CHG NOTICE 1
Abstract: This standard covers the common maintainability design requirements to be used in military specifications for avionic and electronic systems and equipment. -
MIL-L-23398D (2)
Subject(s) : Corrosion preventative , Friction reduction , Material safety data sheet , Qualified products list (QPL) , -
A-A-1858A
Abstract: The General Services Administration has authorized the use of this commercial item description in preference to Federal Specification W-L-00116D/GEN and W-L-00116/49. -
MS24334 REV E
Abstract: THIS SPECIFICATION IS APPROVED FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE.
THE REQUIREMENTS FOR ACQUIRING THE PRODUCT(S) DESCRIBED HEREIN SHALL CONSIST OF THIS SPECIFICATION SHEET AND THE ... -
MIL-F-85675
Abstract: This specification establishes the design, performance, and acceptance requirements for F-1556/ARC UHF Bandpass Filter hereinafter referred to as the filter. The filter is electronically tuned and operates in the Ultra ...Subject(s) : AN/ARC-182 (V) Radio Set , Bandpass , E-2C Aircraft Application , F-1556/ARC , Filter , Harmonic Transmit Rejection , Input Signal Protection , Spurious Rejection , Transmit Sideband Noise Rejection , Ultra High Frequency (UHF) , -
MIL-A-85802
Abstract: This specification establishes the requirements for the manufacture and inspection of one type of electromechanical linear actuator. The test limits in this specification define minimum acceptable capabilities. Intended ...Subject(s) : Actuator , electromechanical , linear , Actuator , plunger force , -
W-L-101/74A
Abstract: This specification sheet was approved by the Commissioner, Federal Supply Service, General Services Administration, for the use of all Federal agencies.
(This specification sheet forms a part of the latest issue of ... -
A-A-1845A
Abstract: The General Services Administration has authorized the use of this commercial item description in preference to Federal Specification W-L-00116D/GEN and W-L-00116/12A. -
MIL-T-22821C
Abstract: This specification covers the general requirements for tachometer generators. It is not complete in itself, but should be used in conjunction with MIL-S-81963 which will form an inherent part of this specification.
The ...Subject(s) : Axis error voltage , Damping tachometer generators , Electromechanical device , First article , Frequency sensitivity , Heater compensated , In-phase linearity , In-phase transformation ratio , Integrating tachometer generator , Network compensated , Output winding , Position error voltage , Quadrature-phase , Qualification , Qualified products list (QPL) , Quality conformance , Rate tachometer generators , Servocomponent , Specification , Speed-sensitive transformation ratio , Temperate sensitivity , Voltage sensitivity , Warm-up time , Zero speed voltage , -
W-L-101/60A
Abstract: This specification sheet was approved by the Commissioner, Federal Supply Service, General Services Administration, for the use of all Federal agencies.
(This specification sheet forms a part of the latest issue of ... -
MIL-W-85635
Abstract: This specification covers the requirements for the manufacture and inspection of a CWU-62/P anti-exposure coverall water test device. Intended Use: The water test device described in this specification is ... -
MIL-C-5646F (2)
Abstract: QUALIFIED PRODUCTS LIST OF PRODUCTS QUALIFIED UNDER MILITARY SPECIFICATION MIL-G-21164 GREASE, MOLYBDENUM DISULFIDE (FOR LOW AND HIGH TEMPERATURES)
This list has been prepared for use by or for the Government in the ... -
MIL-C-22442/13D
Abstract: Inactive for new design after 20 April 1984. For new design use MIL-C-22442/22.
This specification sheet is approved for use by the Naval Air Systems Command, Department of the Navy, and is available ...