درباره ما
ECIA - Electronic Components Industry Association: Recent submissions
Now showing items 21-40 of 507
-
ECA IS-749
Abstract: This test procedure determines the expected wear-out lifetime for aluminum electrolytic capacitors. It provides a measure of the operating time required for parametric changes to cause capacitors to become unusable as ... -
ECA EIA-740
Abstract: This standard defines the dimensions and interconnections of 88.9 mm (3.5 in) small form factor disk drives.
The purpose of this standard is to define the external characteristics of small form factor disk drives so ... -
ECA EIA-364-20D
Abstract: This standard applies to electrical connectors, sockets and coaxial contacts.
Object
The object of this test is to describe a method for measuring the withstanding voltage. -
ECA EIA-541
Abstract: This standard applies to several different categories of electrostatic protective packaging materials. These packaging materials may possess certain electrostatic properties such as to prevent triboelectric charging ... -
ECA EIA RS-443
Abstract: The intent and purpose of this document is to:
(1) Establish a standard reference for determining and defining parameters needed to specify ac Solid State Relays (SSR) and Hybrid Solid State Relays (HSSR) which employ ... -
ECA 331
Abstract: This Standard is intended to specify the jack and plug wiring for proper polarization and channel reproduction. It is also intended to specify phones marking for left and right when they are marked. This Standard covers ... -
ECA EIA-540J0AB
Abstract: The cylindrical battery holders of assessed quality covered by this Detail Specification have: — Maximum enclosure dimensions as shown in figure 2. — A working voltage not exceeding 12 V ac.
— Current ... -
ECA EIA-463-B
Abstract: This Standard covers the requirements for aluminum electrolytic capacitors, nonpolarized, sealed in plastic or aluminum cases, which are for intermittent service starting single phase alternating current induction motors. ... -
ECA RS-348
Abstract: PURPOSE
The purpose of this standard is to eliminate confusion, by providing definitive statements of the conventions involved in determining the polarity of a magnetic field, and by describing basic ... -
ECA EIA-327-A
Abstract: This Standard establishes test methods to verify that the markings or color-coding will not become illegible on the component parts (including printed-wiring boards and excluding electron tubes) when subjected to solvents ... -
ECA 520FAAA
Abstract: The rotary switches of certified quality covered by this detail specification shall:
a) have an indexing angle of 30", 36", 45', 60°, and 90".
b) have maximum switch body dimensions as shown herein.
c) ... -
ECA CB16
Abstract: Foreword
This bulletin was prepared under the cognizance of the Electronic Industries Alliance sector Electronic Components, Assemblies, Equipement & Supplies Association's P-10 Committee on ... -
ECA EIA-364-104A
Abstract: This standard establishes a test method to determine the connector's resistance to burning when exposed to a flame. Burning resistance is defined as the ability to not support or propagate combustion after an ignition ... -
ECA EIA-784
Abstract: This guideline is to be utilized with the ELA standards listed under Clause 3 below.
Introduction
The intent of this EIA Guideline is to provide an editorial addition to two subparts of the ANSI/EIA ... -
ECA RS-297-A
Abstract: This standard applies to 3-contact mating and locking connectors for use in audio circuits. Essentially four types of connectors are covered: male and female portable connectors for use on cables, and male and female ... -
ECA EIA-364-90
Abstract: This procedure applies to interconnect assemblies, such as electrical connectors, sockets and cable assemblies. -
ECA 520AAAF
Abstract: The illuminated and non-illuminated power pushbutton switches of certified quality covered by this detail specification:
a) mount in a panel hole of 19.05 mm (.750 inch) X 28.98 mm (1.141 inch). ... -
ECA TEP 109
Abstract: Purpose and Scope
This document provides recommended test methods for the measurement and ratings of X-ray image intensifier tubes. -
ECA 242
Abstract: The definitions in this standard are to be used to describe Electromagnetic Delay Lines used in pulse circuitry.