درباره ما
ECIA - Electronic Components Industry Association: Recent submissions
Now showing items 1-20 of 507
-
ECA EIA-364-24B
Abstract: This standard establishes a test method to assess the ability of a component to withstand stresses caused by repeated insertion and extraction of contacts during maintenance. This test procedure applies only to connector ... -
ECA EIA-364-1000
Abstract: This standard establishes the test procedures and test sequences to be followed when evaluating the performance of electrical connectors and sockets used in controlled environments. 1) Furthermore, it applies ... -
ECA EIA-540J0AA
Abstract: The cylindrical battery holders of assessed quality covered by this Detail Specification have: - Maximum enclosure dimensions as shown in figure 2.
- A working voltage not exceeding 12 volts (rms). - Current rating not ... -
ECA EIA-364-16A
Abstract: This standard establishes test methods to determine the force required to move a solderless wire wrapped connection along the post parallel to the axis of the post. -
ECA EIA-540C000
Abstract: This sectional specification relates to the sockets, for plug-in relays, of assessed quality. The purpose of this specification is to provide a means of assuring interchangeability between these devices, compatibility ... -
ECA EIA/ECA-747-A
Abstract: This Standard covers requirements for 8mn, 12mm, 16mm and 24mm taping of surface mount components generally less than 1.0mm thick and requiring high precision taping for automatic handling of devices such as singulated ... -
ECA EIA-540F000
Abstract: This Sectional Specification relates to the sockets for Multi-Package Modules of assessed qualtty. The purpose of this Specification is to provide a means of assuring interchange-ability between devices and compatibilrty ... -
ECA EIA-364-107
Abstract: This procedure is applicable to electrical connectors, cable assemblies, or interconnection systems. -
ECA 498B000
Abstract: This Sectional Specification covers a limited range of touch stroke tactile feel switch panels, the bases for which are etched type printed circuit boards. These switch panels are intended for use in low input rate data ... -
ECA EIA-481-D
Abstract: This Standard covers requirements for taping surface mount components. Complementary standards for specialized taping requirements are included in the addendum. -
ECA 540B000
Abstract: This sectional specification relates to the sockets for Pin Grid Array devices of assessed quality. The purpose of this specification is to provide a means of interchange ability between qualified devices and compatibility ... -
ECA EIA-364-92
Abstract: Object
The object of this test procedure is to assess the ability of an insulation displacement connection to withstand the mechanical stress caused by bending the connected wire or ribbon cable in a ... -
ECA EIA-364-80
Abstract: This test procedure describes two methods to measure the shielding transfer impedance of mated cable connectors in the frequency range 10kHz to 100MHz, (method A), and a connector located between a bulkhead panel and a ... -
ECA 520CA00-A
Abstract: Introduction
A blank detail specification is a supplementary document to the sectional specification and contains requirements for style, layout and minimum content of detail specifications.
Detail specifications ... -
ECA EIA-364-11B
Abstract: This procedure is to determine the ability of connector materials to withstand solvents that may be used to clean components.
NOTE—The test solutions indicated herein shall be considered as test mediums only. ... -
ECA EIA-520DAAC
Abstract: The standard size, four pole watertight toggle switches of certified quality covered by this detail specification
a) mount in a 12.4 mm (.49 inch) diameter mounting hole.
b) have a maximum rated voltage of 277 ... -
ECA EIA-364-06C
Abstract: This standard establishes test methods to determine the resistance of mated connector contacts attached to lengths of wire by measuring the voltage drop across the contacts while they are carrying a specified current. -
ECA EIA-654
Abstract: The Soldering Technology Committee (STC) of the Electronic Components, Assemblies & Materials Association, the electronic component sector of Electronic Industries Alliance prepared this specification. -
ECA 213
Abstract: All test points shall be compatible in ali respects with the latest issue of EIA Standard RS-188, Standard Dimensional System for Automation Requirements.
All test points shall be brought out to any three edges of the ...