درباره ما
ECIA - Electronic Components Industry Association: Recent submissions
Now showing items 61-80 of 507
-
ECA EIA-364-94
Abstract: Object
The object of this test procedure is to determine the force necessary to remove the wire within the connection slot of an accessible insulation displacement termination along the longitudinal ... -
ECA EIA-364-103
Abstract: This standard is applicable to electrical connectors, sockets, cable assemblies or interconnection systems. -
ECA TEP 173
Abstract: These statistics apply to the measurement of x-radiation emitted from high voltage rectifiers and shunt regulators. These x-radiations' are considered as the soft x-ray variety emanating from the tube and produced by an ... -
ECA EIA-364-71C
Abstract: This standard applies to connectors and sockets that are mounted to printed wiring boards (PWB) employing through mount technology. -
ECA EIA-520AAAB-A
Abstract: The family of momentary contact, non-sensitive pushbutton switches covered by this detail specification:
a) mount in a panel hole with a clearance diameter for a 1/4-32UNEF-2A thread.
b) have a maximum rated voltage ... -
ECA TEP 138
Abstract: Preface
This publication describes in considerable detail a method for measuring noise figure of RF amplifier tubes in the receiving tube class.
This method is intended for use in obtaining noise figure ... -
ECA 502-A
Abstract: This test method applies to the measurement of x-radiation emitted from non-raster-scanned direct-view cathode ray tubes. For some applications the test procedures described in Recommended Standard EIA-501, "Recommended ... -
ECA TEP105
Abstract: PREFACE
This publication includes all test methods developed by the JT-20 Committee on Electro-optic Devices for use in testing industrial cathode ray tubes, They are intended to be useful in evaluating ... -
ECA EIA-364-08B
Abstract: This standard establishes a test method to determine the tensile strength of a crimped contact to conductor joint. The values obtained give an indication of the relative strength of the joints. Unless otherwise specified ... -
ECA EIA-364-04A
Abstract: This procedure establishes two methods to determine the magnitude of normal force, at the point of the electrical connection, generated by a contact system at a given deflection within its normal operating levels. This ... -
ECA EIA-296-F
Abstract: This Standard includes the lead taping requirements for components having axial configured leads, provided these components may be taped in accordance with the requirements of this document.
PURPOSE ... -
ECA CB 4
Abstract: INTRODUCTION
For many years the question of the minimum wire size which could be safely used for wirewound resistors has been debated. In Military specifications the minimum wire diameter has been specified which ... -
ECA EIA-540DAAB
Abstract: The Dual In-Line Sockets of assessed quality covered by this Detail Specification shall have:
a) Maximum enclosure dimensions (See Figure 1 and TaMe 1A).
b) Working voltage not to exceed 250 volts (rms).
c) ... -
ECA EIA-364-106
Abstract: This standard establishes test methods to evaluate existing standing wave ratio (SWR) of connectors, coaxial, radio frequency (RF). Measured SWR shall not exceed that specified over the frequency range specified. -
ECA 417-A
Abstract: This standard establishes the external dimensions of envelopes for the encapsulation of quam resonators in their sealed or closed configuration. To the extent found feasible the outlines are arranged in "families", with ... -
ECA 540AA00
Abstract: The Chip Carrier Sockets of assessed quality covered by this detail specification shall have:
a) Maximum enclosure of (maximum length, width and height dimensions).
b) A rated voltage not exceeding _ volts (rms). ... -
ECA EIA-704-A
Abstract: This Standard provides requirements for packaging components for automatic handling using mechanically-interlocking cover tape and carrier tape. -
ECA EIA-448-24
Abstract: Purpose
The purpose of this test method is to establish a standard for measuring the transfer time of switches with solid state circuit outputs. This standard applies to devices such as manually operated ... -
ECA EIA-540ADAA
Abstract: The Quad Flat Pack carrier of assessed quality covered by this detail specification shall have:
a) Maximum enclosure dimensions (See Figure 1 and Table 1).
b) Working vdtage not to exceed 250 volts (rms).
c) ... -
ECA 520EAAB
Abstract: The Dual In-line Machine Insertable Switches of certified quality covered by this Detail Specification:
Have maximum enclosure dimensions of 32.5 mm (1.280 inch) long, 7.26 (0.286) wide and 4.57 (0.180) high.
Have ...