درباره ما
ECIA - Electronic Components Industry Association: Recent submissions
Now showing items 81-100 of 507
-
ECA IS-43AE
Abstract: This Detail Specification defines Type 2 Nonplenum cable used with the Token Ring LAN Cabling System. Type 2 NP consists of 2 twisted pairs of Data Grade Media (DGM) shielded with aluminum tape and braided shields, all ... -
ECA EIA-198-3-E
Abstract: Prior to printing a review was conducted of current EIA Standards and a list of documents that could have bearing on this standard was assembled. For the purposes of this revision, no attempt was made to review all documents ... -
ECA 520F000-A
Abstract: This sectional specification relates to electromechanical rotary switches of certified quality. These families of switches are for use in electronic, communication and other low power applications.
Switches covered ... -
ECA EIA-364-28F
Abstract: The standard test procedure details a method to assess the ability of electrical connector components to withstand specified severities of vibration. -
ECA 395-1
Abstract: The following Detail Specification covers standard case sizes, termination details, and requirements for tubular aluminum electrolytic capacitors with wire terminations at one end. -
ECA 520EAAA
Abstract: The Dual In-line Surface Mountable Switches of certified quality covered by this Detail Specification:
Have maximum enclosure dimensions of 32.5 mm (1.280 inch) long, 7.26 (0.286) wide and 4.57 (0.180) high.
Have ... -
ECA EIA-364-12A
Abstract: This standard establishes a test method to determine the ability of socket contacts, classified as restricted entry types, to prevent the insertion of an oversized pin. -
ECA 520AA00
Abstract: The (applicable modifiers t o describe the type of pushbutton switch covered by this Detail Specification ) pushbutton switches of certified quality covered by this Detail Specification:
a) mount in a panel hole of ( ... -
ECA EIA-967
Abstract: This specification defines the terminology and physical requirements for the mating interface and physical characteristics of the Micro SAS Connector System. It is designed to support high speed serial signals and power. ... -
ECA 527
Abstract: This Recommended Standard defines the method for establishing the relationship between the inside face panel edge geometry and the minimum published screen dimensions for shadow-mask color TV picture tubes and color monitor ... -
ECA EIA-280-C
Abstract: This standard establishes the minimum requirements to produce mechanically and electronically stable solderless wrapped electrical connections made with single, solid, round wire and appropriately designed terminals. ... -
ECA EIA-364-66A
Abstract: This standard establishes test methods for the measurement of the EMI shielding effectiveness of electrical connectors over the frequency range of 1.0 GHz to 10.0 GHz using the mode-stirred technique. The procedure applies ... -
ECA EIA-616-A
Abstract: This standard is applicable to modular two-part connectors for printed wiring boards associated with equipment for telecommunication or electronic devices using similar techniques. The standard covers high-density connectors ... -
ECA TEP105-10
Abstract: Introduction
Contrast ratiois defined as the ratio of the luminance of an excited area of the CRT screen to that of an unexcited or dark area of the screen.
Contrast is normally measured under various ambi ... -
ECA 480
Abstract: These recommendations relate to toggle switches for use in equipment for electrical and electronic devices, including switches necessary to connect the supply mains. These switches are not intended to be used in electrical ... -
ECA EIA-477-A
Abstract: This document relates to crystalline quartz produced by hydrothermal growth intended to be used as raw material for piezoelectric crystal devices. -
ECA 446-4
Abstract: The following details apply to the standard illuminated non-sensitive puchbutton switches covered by this detail specification:
(a) Will snap-in mount in a .625 ± .O05 (15.88 ± .13 mm)
(b) Have ... -
ECA EIA/ECA-932
Abstract: Description
This specification defines the qualification program for surge withstand telecommunication fuses. Fuses covered will be limited to axial-leaded, radial-leaded and surface mount configurations ...