درباره ما
ECIA - Electronic Components Industry Association: Recent submissions
Now showing items 161-180 of 507
-
ECA RS-448-2
Abstract: PURPOSE
The purpose of this standard is to evaluate electromechanical components which have been subjected to the environmental effects of machine soldering and the associated fluxing, preheating, and cleaning ... -
ECA EIA-476-B
Abstract: This standard describes a system for identification of the date of manufacture of an electronic component or equipment through the manufacturer′s marking the product with a series of numbers known as the EIA date ... -
ECA EIA-364-02D
Abstract: This standard establishes a method to determine the integrity of the seal of the shell, insert and contact interfaces in an electrical connector.
Object
The air leakage test may be conducted as one of the tests in ... -
ECA EIA-677
Abstract: This standard defines the pin dimensions of the 4-pin pin-and-socket connector commonly used to provide power to small form factor disk drives.
The purpose of this standard is to define the pin dimensions so that ... -
ECA EIA-772-A
Abstract: This guide has been prepared to aid the circuit and system designer in the selection of supplemental fuses. Traditionally, these have been fuses that interrupt the primary equipment power source when an overcurrent condition ... -
ECA EIA/ECCB-952
Abstract: This document defines the requirements for documenting processes to assure customers and users of given products or sets of products, that their lead content is known. This document does not contain detailed descriptions ... -
ECA EIA-IS-47
Abstract: Soldering of SMT components is performed, in general, at a relatively low soldering temperature (215°C). Thus, the reflow characteristics of the finish must be carefully considered. In addition, the solder joint itself ... -
ECA EIA-364-31C
Abstract: This standard establishes test methods for the evaluation of connectors and sockets as they are influenced by the effects of high humidity and heat. -
ECA EIA-364-19A
Abstract: This standard establishes test methods to determine the ability of the insert retaining system to withstand the torsional stresses likely to be encountered during normal usage.
Typical damage resulting £rom this ... -
ECA IS-43AA
Abstract: This Detail Specification defines Type 1 Outdoor cable used with the Token Ring LAN Cabling System. Type 1 OD consists of 2 twisted pairs of Data Grade Media (DGM) shielded with corrugated aluminum, filled with a waterproofing ... -
ECA EIA/ECA-469-D
Abstract: This document provides terminology, methods, and criteria for characterizing the internal structural features of monolithic, ceramic dielectric capacitors. Its major objective is the accurate evaluation of the internal ... -
ECA 520C000
Abstract: This sectional specification applies to the sensitive switch family of special-use electromechanical switches of certified quality. Sensitive switches covered by this standard have a rated voltage not exceeding 500 volts ... -
ECA EIA-364-83
Abstract: This standard test procedure applies to mated plugs and receptacles or mated plugs and receptacles mounted to a bulkhead with conductive shells and/or mounting flange. -
ECA EIA-717-A
Abstract: Description
This specification defines the qualification program for surface mount tantalum and niobium capacitors. Table 2 lists the tests required. Specification sheets can be added, as ... -
ECA TEP105-15
Abstract: Introduction to the Glass and Screen Aqeinq Procedures
This procedure is broken down into three subsections. They are:
I. Glass Ageing
This procedure tests the ageing properties of CRT glass alone, ... -
ECA 153-B
Abstract: This standard outlines electrical, mechanical, and environmental requirements for commercial capacitors which have a natural mica dielectric and wire lead terminations.
It is a standard covering a variety of case sizes, ... -
ECA EIA-364-63
Abstract: This test procedure establishes a test method to determine whether accessory thread strength and portion of the connector that accepts cable clamps and "J" adaptors shall be capable of withstanding torque requirements ... -
ECA 705
Abstract: This document defines the means for review and registration of new technologies pertaining to automated handling of electronic components. -
ECA RS-176
Abstract: This standard covers iron core pulse transformers for use in radar transmitters and similar equip ment where long life, reliability and continuity of operation are essential. -
ECA 495-A
Abstract: This Standard describes some of the requirements for film dielectric capacitors oil filled or impregnated, or both, made with two metallized paper electrode or one metallized paper electrodes and one aluminum foil electrode. ...