درباره ما
Browsing EIA - Electronic Industries Alliance by Issue Date
Now showing items 1-20 of 27
-
EIA RS-192-A
Abstract: INTRODUCTION
This standard, which shows quartz crystal unit holder outlines and pin connections, includes the outlines previously shown in RETMA Standard RS-192, July 1957; those of interest to the U. ... -
EIA RS-186-E
Abstract: This Standard establishes uniform methods for testing electronic component parts. In case of conflict between this Standard and any individual component standards or detail specifications, the requirements of the individual ... -
EIA RS-186-8E
Abstract: PURPOSE
This sinusoidal high frequency vibration test is performed for the purpose of determining the effect on component parts of vibration in the frequency range of 10 to 500 Hz or 10 to 2000 Hz as ... -
EIA RS-186-9E
Abstract: This standard defines a test for solderability of solid lead wires, terminals, and conductive accessories of component parts which are to be joined b a soldering operation involving the use of rosin type flux and solder ... -
EIA RS-186-12E
Abstract: PURPOSE
This test is performed to determine the effect of storing or operating component parts at elevated temperatures for various time periods. Different degrees of severity as prescribed by temperature ... -
EIA RS-186-5E
Abstract: PURPOSE
The salt spray test is performed for the purpose of determining the adequacy of protective coatings or finishes, and has been widely used to evaluate the resistance of metals to corrosion in ... -
EIA RS-186-11E
Abstract: PURPOSE
This test is conducted for the purpose of determining the resistance of a component part to exposures at ! extremes of high and low temperatures in air, and to the shock of alternate exposures ... -
EIA RS-186-13E
Abstract: PURPOSE
This test is to measure the resistance offered by the insulating members of a component part to an impressed direct voltage tending to produce a leakage of current through or on the surface of ... -
EIA RS-186-4E
Abstract: PURPOSE
This dielectric test is performed for the purpose of determining the ability of component parts to withstand a potential at sea level or at a specified altitude. The potential used is normally ... -
EIA RS-186-1E
Abstract: PURPOSE
This test is intended to evaluate the effect of absorption and diffusion of moisture and moisture vapor on component parts. The test in an artificial environmental test, accelerated to shorten ... -
EIA RS-186-3E
Abstract: PURPOSE
This test is intended to evaluate the effect of absorption and diffusion of moisture and moisture vapor on component parts. The test is an artificial environmental test and is severely accelerated ... -
EIA RS-186-10E
Abstract: PURPOSE
This test is performed to determine the effect of normal soldering operations on component parts. Excessive changes in electrical characteristics or mechanical damage to a component part are ... -
EIA RS-186-2E
Abstract: PURPOSE
This test is intended to evaluate in an accelerated manner, the resistance of component parts to deterioration resulting from high humidity and heat conditions typical of tropical environments. ... -
EIA RS-186-6E
Abstract: PURPOSE
These tests are intended to determine the ability of terminals to withstand the usual stresses which may be applied during assembly or disassembly operations. Several types of tests are provided ... -
EIA RS-186-7E
Abstract: PURPOSE
This vibration fatigue test is performed for the purpose of determining the ability of component parts and their mountings to withstand vibration in the low frequency range of 10 to 55 Hertz. ... -
EIA EIA-512
Abstract: Methods are described which permit determination of fhe values of the equivalent electrical parameters of piezoelectric quartz crystal units, utilizing automated measuring equipment. The methods described make use of ... -
EIA EIA-186-14E
Abstract: PURPOSE
This test is intended to determine the effectiveness of panel seals on electronic components which are intended for mounting through holes in panels or enclosures. The panel seals are exposed to water under ... -
EIA CB6-A
Abstract: This document has been compiled in response to a generally expressed desire on the part of both users and manufacturers for a guide to the use of quartz crystal units for frequency control so that they may be used to their ... -
EIA EIA-541
Abstract: This standard applies to several different categories of electrostatic protective packaging materials. These packaging materials may possess certain electrostatic properties such as to prevent triboelectric charging ... -
EIA EIA-512-1
Abstract: This guide is intended to supplement EU-512, "Standard Methods of Measurement of Equivalent Electrical Parameters of Quartz Crystal Units, 1 kHz to 1 gHz." Frequent mention of the standard is made, and having the standard ...